Home Productos Pantalla OLED Módulos OLED Con Táctil WEO012864J-CTP

12864, 2.42 pulgada Módulos OLED Con panel táctil capacitivo

Modelo Nº WEO012864J-CTP

►Tipo : Gráfico
►Estructura : COG+PCB
►Tamaño : 2.42 pulgada
►Matriz de puntos 128 x 64
►Controlador integrado SSD1309
►Fuente de alimentación de 3V
►1/64 duty
►Interfaz : 8080 opción 6800, SPI, I2C
►Con panel táctil capacitivo (CTP)
►Detect Point : 1 Finger
►Color de la pantalla: Blanco / Amarillo / Azul cielo / Verde

DIBUJO

12864, 2.42 inch OLED Display Module with Capacitive Touch Panel - WEO012864J-CTP

Data source ref: WEO012864JWPP3D00000

ESPECIFICACIONES

Función interfaz Pin

No. Símbolo Función
1 VDD Power supply pin for core logic operation
2 VSS Ground.
3 NC(GND) No connection
4~11 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
12 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
13 NC(GND) No connection
14 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
15 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
16 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
17 E This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
18 NC(GND) No connection
19 DISP No Connection
20 NC(GND) No connection
21 TP_INT Interrupt signal, active low, asserted to request
Host start a new transaction
22 TP_SDA I2C data signal
23 TP_SCL I2C clock signal
24 TP_RST External reset signal, active low

Datos mecánicos

Elemento Dimensión Unidad
Matriz de puntos 128 x 64
Dimensión del módulo 75.0 × 52.7 ×10.2 MAX mm
zona activa 55.01 × 27.49 mm
Tamaño del punto 0.40 × 0.40 mm
Distancia entre puntos 0.43 × 0.43 mm
Modo de visualización Matriz pasiva
Color de la pantalla Monocromos
Drive Duty 1/64 Duty
IC SSD1309
Interfaz 8Bits 6800 , opcional 8080 / 4-SPI / I2C
Tamaño 2.42 pulgada
PCAP IC GT911
Detect Point 1
PCAP Interfaz I2C
Superficie Deslumbramiento

Valores nominales máximos absolutos

Parameter Símbolo Valor mín. Valor máx. Unidad
Supply Voltage for Logic VDD -0.3 4 V
Temperatura de funcionamiento TOP -20 +70 °C
Temperatura de almacenamiento TSTG -30 +80 °C

Características electrónicas

DC Características electrónicas

Elemento Símbolo Condition Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current IDD VDD =3V - 150 300 mA

Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42" oled, 2.42 inch oled, oled 2.42, oled 2.42"

go top
close