На главную страницу Продукция OLED Дисплей Графический OLED дисплей WEF012864Q

2.7", 128x64 COG OLED дисплей С рамкой

Артикул. WEF012864Q

►Тип: Графический
►Тип монтажа контроллера: COG + Frame
►Диагональ: 2.7 дюйма
►Разрешение: 128 x 64 точек
►IC:SSD1309
►3V Power supply
►1/64 duty
►Интерфейс: 6800, 8080, SPI, I2C
►Цвет дисплея: Белый / Желтый / Небесно голубой / Зеленый

Описание

WinSTAR OLED-дисплей WEF012864Q представляет собой модуль дисплея с пассивной матрицей OLED-2.7” (128x64 точек). Этот графический дисплей имеет встроенный IC SSD1309, с поддержкой 6800/8080 8-бит, I2C и 4-wire интерфейсов. WEF012864Q обладает размером модуля 89,7 х 47,2 мм,с активной площадью 61,41 х 30,69 мм; Модель WEF012864Q является COG OLED заменой TAB OLED WEX012864L, которая была снята с производства. 

Преимуществом этих 2.7” COG OLED индикаторов WEF012864Q – является легкий вес и низкое энергопотребление, что идеально подходит для измерительных устройств, домашних приложений, POS-систем, Cloud / IoT-систем, интеллектуальных технологических устройств, энергетических систем, систем связи, медицинских инструментов и т. Д. Модуль WEF012864Q OLED может работать при температурах от -40 ℃ до + 80 ℃, а температура хранения от -40 ℃ до + 80 ℃.

Чертеж

2.7 inch 128x64 COG OLED Display - WEF012864Q
Data source ref: WEF012864QWPP3N00000

Технические характеристики

Функции контроллера контактного интерфейса

No. Символы Описание
1 NC No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX Parallel 0 1
8-bit 80XX Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 VDD Power supply pin for core logic operation
22~28 NC No connection
29 VSS Ground.
30 NC No connection

Механические характеристики

Наименование Измерения Единица
Разрешение 128 x 64 точек
Габариты 89.7 × 47.2 × 3.4 mm
Активная область 61.41 × 30.69 mm
Размер пикселя 0.45 × 0.45 mm
Шаг пикселя 0.48 × 0.48 mm
Матрица Пассивная матрица
Цвет дисплея монохромные
Рабочий цикл 1/64 Duty
IC SSD1309
Интерфейс I2C, 4-Wire SPI ,6800, 8080
Диагональ 2.7 дюйма

Абсолютные максимальные значения

Parameter Символы Минимальный Максимальный Единица
Напряжение питания логических схем VDD -0.3 4 V
Напряжение питания дисплея VCC 0 15 V
Диапазон рабочих температур TOP -40 +80 °C
Температура хранения TSTG -40 +85 °C

Электронные характеристики

Наименование Символы Кондиция Минимальный Типичный Максимальный Единица
Напряжение питания логических схем VDD 2.8 3.0 3.3 V
Напряжение питания дисплея VCC 12.5 13 13.5 V
Вход высокого уровня VIH 0.8×VDD V
Вход низкого уровня VIL 0.2×VDD V
Выход высокого уровня VOH 0.9×VDD V
Выход низкого уровня VOL 0.1×VDD V
50% Check Board operating Current VCC =13.0V  - 22 33 mA

Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 дюйма oled, oled 2.7
go top
close