설명
WEN025664B 모델은 3.12인치 대각선 크기와 256x64 도트의 해상도를 갖춘 COF Graphic OLED입니다. 이 OLED 모듈은 SSD1322 IC를 내장하고 있으며, 8비트 6800/8080 및 3/4라인 SPI 인터페이스를 지원합니다. 외형 크기는 89.2 × 44.0 mm이며, 활성 영역 크기는 76.78 × 19.18 mm입니다. 또한 3V의 논리 전압을 지원하며, 50% 체크 보드에서의 전류는 150mA @3.0V VDD (평균 값)이며, 드라이빙 듀티는 1/64입니다.
이 모듈은 내장 PCB를 갖추고 있어 고객이 응용 프로그램에 대한 추가 PCB 개발 없이 와이어 연결을 사용할 수 있습니다. 또한 PCB에 통합 된 VCC 회로는 고객의 사용을 간소화합니다. 이 PCB 보드는 네 개의 마운팅 홀을 갖추어 고객이 모듈을 쉽게 응용 프로그램에 고정할 수 있는 방법을 제공합니다. 이 OLED 모듈은 스마트 홈 응용, 의료 기기, 산업 제어 등에 적합합니다.
WEN025664B 모델은 -40℃에서 +80℃의 온도 범위에서 작동할 수 있으며, 저장 온도는 -40℃에서 +85℃까지입니다. OLED 모듈은 10,000:1의 높은 명암비를 제공하여 낮은 조명 환경에서 향상된 이미지 품질, 뚜렷한 디테일 및 향상된 가독성을 실현합니다.
또한, 동일한 크기의 OLED 패널은 다양한 대안을 제공합니다:- WEX025664B 시리즈 - 금속 프레임 및 PCB 없음
- WEX025664B-CTP 시리즈 - 금속 프레임, PCB 없이 CTP 터치 스크린이 장착되어 있음
- WEN025664B-CTP 시리즈 - 금속 프레임, PCB 및 CTP 터치 스크린이 장착되어 있음
도면
Data source ref: WEN025664BWAP3N0000
사양
인터페이스 핀 기능
Pin Number |
기호 | I/O | 기능 | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | P | Ground. | ||||||||||
2 | VDD | P | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
3 | N.C. | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
4 | D/C# | I | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
5 | R/W# (WR#) |
I | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
6 | E/RD# | I | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
7~14 | DB0 | I/O | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, DB1 will be the serial data input SDIN and DB0 will be the serial clock input SCLK. |
||||||||||
DB1 | |||||||||||||
DB2 | |||||||||||||
DB3 | |||||||||||||
DB4 | |||||||||||||
DB5 | |||||||||||||
DB6 | |||||||||||||
DB7 | |||||||||||||
15 | NC | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
16 | RES# | I | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
17 | CS# | I | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
18 |
NC | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
19 | BS1 | I | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDD |
||||||||||
20 | BS0 | ||||||||||||
21~24 | NC | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
기계적 데이터
항목 | 치수 | 단위 |
---|---|---|
도트 매트릭스 | 256 x 64 Dots | - |
모듈 치수 | 89.2 × 44.0 × 3.3 Max. | mm |
활성 영역 | 76.78 × 19.18 | mm |
도트 크기 | 0.278 × 0.278 | mm |
도트 피치 | 0.3 × 0.3 | mm |
디스플레이 모드 | 패시브 매트릭스 | |
디스플레이 색상 | Monochrome | |
Drive Duty | 1/64 Duty | |
Gray Scale | 4 bits | |
IC | SSD1322 (COF) | |
인터페이스 | 6800, 8080, SPI | |
크기 | 3.12 인치 |
절대 최대 정격값
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Supply Voltage for Display | VDD | -0.3 | 4 | V |
작동 온도 | TOP | -40 | 80 | °C |
보관 온도 | TSTG | -40 | 85 | °C |
전기적 특성
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
High Level Input | VIH | - | 0.8×VDD | - | VDD | V |
Low Level Input | VIL | - | 0 | - | 0.2×VDD | V |
High Level Output | VOH | - | 0.9×VDD | - | VDD | V |
Low Level Output | VOL | - | 0 | - | 0.1×VDD | V |
50% Check Board operating Current | IDD | VCC =3V | - | 150 | 300 | mA |
Search keyword: 256x64 oled, oled 256x64, 3.12 oled, 3.12" oled, 3.12 인치 oled, oled 3.12, oled 3.12인치