首頁 產品介紹 OLED顯示器 繪圖型 OLED 顯示器 WEO025664A-ZIF

2.08吋, 256x64 OLED模組 (ZIF FPC)

型號 WEO025664A-ZIF

►類型: 繪圖型
►結構: COG + ZIF FPC
►尺寸: 2.08吋
►256x64 點陣
►內建控制器 SSD1362
►3V電源電壓
►1/64 duty
►介面: 6800, 8080, SPI, I2C
►發光顏色: 白色 / 黃色
►支援灰階
►其它FPC選項請參閱最下方表格說明

產品敘述

WEO025664A-ZIF是一款2.08吋繪圖型COG OLED顯示器模組,解析度256x64 pixels。此款模組內建SSD1362 驅動 IC,模組操作支援 6800/8080 8-bit 並列介面,I2C與3線及4線SPI介面,支援4 bits 灰階模式,3V電壓驅動,1/64 duty,以棋盤格50%畫素點亮畫面測試,VCC用12V點亮時耗電流15mA。此2.08吋COG結構的 WEO025664A-ZIF模組工作溫度是-40℃至 80℃,儲存溫度-40℃至 85℃。

WEO025664A-ZIF是COG超薄化結構的OLED顯示器,自發光無需背光非常輕薄,低耗電流,非常適用於智能家電、量測儀器、可攜帶式裝置、智慧醫療產品、個人健康守護追蹤裝置等產品。

規格圖

2.08 OLED Display Module 256×64 -  WEO025664A-ZIF -Winstar Display

Data source ref: WEO025664ALAP3N00000

產品規格

Pin功能定義

No. 符號 功能
1 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VP This pin is the segment pre-charge voltage reference pin.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
4 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
5 VDD Power supply for core logic operation.
VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.
A capacitor should be connected between VDD and VSS under all circumstances.
6 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
7 IREF This pin is the segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA.
When internal IREF is used, this pin should be kept NC.
8 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
9 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
10 VSS Ground pin. It must be connected to external ground.
11 VSS Ground pin. It must be connected to external ground.
12 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
13 BS0 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1, BS0 are pin select.
BS[2:0] Interface
000 4 line SPI
001 3 line SPI
110 8-bit 8080 parallel
100 8-bit 6800 parallel
010 I2C
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
14 BS1
16 BS2
15 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
17 CS This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS is pulled LOW (active LOW).
In I2C mode, this pin must be connected to VSS.
18 RES This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
19 D/C This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
20 R/W This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
21 RD This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
22 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
23 D1
24 D2
25 D3
26 D4
26 D5
28 D6
29 D7
30 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
31 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

規格說明

項目 規格 單位
解析度 256 x 64 Dots
模組尺寸 60.5 x 19.0 x 1.61 mm
有效區域 51.18 x 12.78 mm
像素大小 0.18 x 0.18 mm
像素間距 0.2 x 0.2 mm
顯示模式 被動矩陣
顯示顏色 單色
驅動方式 1/64 Duty
灰階 4 Bits
IC SSD1362
介面 3線和4線 SPI, I2C, 6800, 8080
尺寸 2.08 吋

最大絕對額定值

參數 符號 最小值 最大值 單位
工作電源電壓 VCI -0.5 5.5 V
邏輯電源電壓 VDD -0.5 2.75 V
顯示電源電壓 VCC -0.5 21 V
工作溫度 TOP -40 80 °C
儲存溫度 TSTG -40 85 °C

電氣特性

DC電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VCI 2.8 3.0 3.3 V
邏輯電源電壓 VCC 11.5 12 12.5 V
輸入高電壓 VIH 0.8×VCI VCI V
輸入高電壓 VIL VSS 0.2×VCI V
輸出高電壓 VOH 0.9×VCI VCI V
輸出低電壓 VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=12V 15 30 mA

FPC options

Drawing FPC Length PIN Pitch ZIF or HOTBAR FPC Interface FPC No. Create Date
FPC2070002401XXXXX02_WEO025664ALAP3N00H00 23 24 0.7 HOTBAR 3-Wire and 4-Wire SPI, I2C, 6800, 8080 FPC2070002401XXXXX02 20180611
FPC2030003111XXXXX02_WEO025664ALAP3N00000 21 31 0.3 ZIF 3-Wire and 4-Wire SPI, I2C, 6800, 8080 FPC2030003111XXXXX02 20171107
go top
close