128x64 COG点阵液晶显示屏

型号 WO12864D3

►COG LCD显示模块
►类型: 图形
►结构: COG
►尺寸: 2.93英寸
►128x64 点阵
►IC: ST7565P
►3.3V电源电压
►1/64 duty cycle
►接口:6800/8080/SPI

PDF下载

索取Demo Code 产品询问

上一个产品回分类页下一个产品

规格图

Winstar WO12864D3 - 128x64 COG Displays (Chip on Glass Display)

Data source ref:WO12864D3-TFH#

产品规格

Pin功能定义

Pin No.

符号

Level

说明

/CS1

The chip select signal

/RES

When RES is set to “L”, the setting are initialized.

This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.

/WR(R/W)

• When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.

/RD(E)

• When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
• When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.

6~13

D0~D7

I/O

Data bus line

VDD

Power
Supply

Power supply

VSS

Power
Supply

Ground

VOUT

DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD

CAP5+

DC/DC voltage converter

CAP3+

CAP1-

CAP1+

CAP2+

CAP2-

CAP4+

VRS

Power
Supply

This is the internal-output VREG power supply for the LCD power supply voltage
regulator.

Power
Supply

This is a multi-level power supply for the liquid crystal drive.

Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
IRS = “L” : the V0 voltage regulator internal resistors are not used.
IRS = “H” : the V0 voltage regulator internal resistors are used.

C86

This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface

P/S

This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:

P/S	Data/Command	Data	Read/Write	Serial Clock
"H"	A0	D0 to D7	/RD,/WR	X
"L"	A0	SI(D7)	Write only	SCL(D6)

When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM

/HPM

This is the power control terminal for the power supply circuit for liquid crystal drive.
/HPM = “H”: Normal mode
/HPM = “L”: High power mode

IRS

This terminal selects the resistors for the V0 voltage level adjustment.
IRS = “H”: Use the internal resistors
IRS = “L”: Do not use the internal resistors. The V0 voltage level is
regulated by an external resistive voltage divider attached to the VR terminal

规格说明

项目	标准尺寸	单位
点阵(分辨率)	128 x 64	－
模块尺寸	80.0 x 54.0 x 9.5	mm
检视区域	70.7 x 38.8	mm
有效区域	66.52 x 33.24	mm
点大小	0.48 x 0.48	mm
点间距	0.52 x 0.52	mm
驱动方式	1/64 , 1/9 Bias
背光类型	LED
IC	ST7565P
界面	6800/8080/4-Line SPI

最大绝对额定值

项目	符号	最小值	典型值	最大值	单位
工作温度	TOP	-20	－	+70	℃
储存温度	TST	-30	－	+80	℃
电源电压	VDD	-0.3	－	3.6	V
Power supply voltage (VDD standard)	V0,VOUT	-0.3	－	14.5	V
Power supply voltage (VDD standard)	V1,V2,V3,V4	-0.3	－	V0+0.3	V

电气特性

项目	符号	条件	最小值	典型值	最大值	单位
逻辑电源电压	VDD-VSS	－	2.7	－	3.3	V
LCM电源电压	V0-VSS	Ta=-20℃ Ta=25℃ Ta=70℃	10.0 9.8 9.6	10.2 10.0 9.8	10.4 10.2 10.0	V V V
输入高电压	VIH	－	0.8 VDD	－	VDD	V
输入低电压	VIL	－	VSS	－	0.2VDD	V
输出高电压	VOH	－	0.8VDD	－	VDD	V
输出低电压	VOL	－	VSS	－	0.2VDD	V
供电电流（不包括LED背光）	IDD	－	－	0.6	1.0	mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd

128x64 COG点阵液晶显示屏

规格图

产品规格

Pin功能定义

规格说明

最大绝对额定值

电气特性

推荐产品

WO12864H

我们重视您的隐私

我们重视您的隐私

管理同意声明