Ana sayfa Ürünler OLED Ekran Grafik OLED Ekran WEO006448B

0.66" 64×48 Grafik OLED Ekran

Model No. WEO006448B

►Türü : Grafik
►Yapı : COG
►Boyut : 0.66 inç
►64 x 48 dot matrisi
►IC:SSD1315
►3V güç sağlayıcı
►1/48 görev
►Ara yüz : 6800, 8080, 4-Wire SPI, I2C
►OLED Rengi: Beyaz / Sarı

Açıklama

 

ÇIZIM

0.66 inch Mini Screen,64x48 pixel OLED Display - WEO006448B

Data source ref:WEO006448BWPP3N0Y000

AYRINTILAR

Arayüz Pin Fonksiyonlari

No. Symbol Fonksiyon
1 ESD_GND It should be connected to ground.
2 C2N C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2P
4 C1P
5 C1N
6 VBAT Power supply for charge pump regulator circuit.
Status VBAT VDD VCC
Enable charge pump Connect to external VBAT source Connect to external VDD source A capacitor should be connected between this pin and VSS
Disable charge pump Keep float Connect to external VDD source Conect to external VCC source
7 VSS This is a ground pin.
8 VDD Power supply pin for core logic operation.
9 BS1 These pins are MCU interface selection input.
See the following table.
  BS1 BS2
12C 1 0
4-wire SPI 0 0
8-bit 6800 Parallel 0 1
8-bit 8080 Parallel 1 1
10 BS2
11 CS# The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
12 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
13 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred.
14 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS
16~23 D0~D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL .
24 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.
When internal IREF is used, this pin should be kept NC.
25 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
26 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
27 VLSS This is an analog ground pin. It should be connected to VSS externally.
28 ESD GND It should be connected to ground.

Mekanik Veri

Kalem Ölçü Birim
Dot Matrix 64 x 48 Dots -
Modül ölçüleri 18.46 × 18.10 × 1.26 mm
Aktif alan 13.42 × 10.06 mm
Nokta boyutu 0.185 × 0.185 mm
Nokta sıklığı 0.210 × 0.210 mm
Display Mode Pasif Matrisli
Display Color Monochrome
Drive Duty 1/48 Duty
IC SSD1315
Arayüz 6800, 8080, 4-Wire SPI, I2C
Boyut (Köşegen) 0.66 inç

Absolute Maximum Ratings

Parameter Symbol Minumum Deger Maksimum Deger Birim
Supply Voltage VDD 0 4.0 V
Charge Pump Regulator Supply Voltage VBAT 0 6.0 V
Supply Voltage for Display VCC 0 18.0 V
Operating Temperature TOP -30 +70 °C
Storage Temperature TSTG -30 +70 °C

Elektronik Özellikleri

Kalem Symbol Durum Minumum Deger Tipik Deger Maksimum Deger Birim
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Supply Voltage for Display (Supplied Externally) VCC 6.0 7.5 15.0 V
Charge Pump Regulator Supply Voltage VBAT 3.0 3.3 VDD V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump VCC 7.0 7.5 0.2×VDD V
Input High Volt VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.1×VDD V
Output High Volt. VOH - 0.9×VDD - 30 V
Output Low Volt. VOL - 0 - 30 V
Display 50% Pixel on (VCC Supplied Externally) ICC VCC=7.5V 3 30 mA
Display 50% Pixel on (VCC Generated by Internal DC/DC)  IBAT - 15 30 mA


Search keyword: 64x48 oled, oled 64x48, 0.66 oled, 0.66" oled, 0.66 inç oled, oled 0.66"

go top
close