Ana sayfa Ürünler LCD Ekran COG LCD Ekran WO12864B

128x64 COG LCD Modül

Model No. WO12864B

►128x64 COG LCD
►Türü : Grafik
►Yapı : COG
►Boyut : 2.82 inç
►122x64 dot matrisi
►IC: ST7565P
►3.3V güç sağlayıcı
►1/65 görev döngüsü
►WO12864B: kalınlık 12.1mm
►WO12864B1: kalınlık 6.0mm
►Ara yüz : 6800/8080/SPI

Açıklama

There are two versions for WO12864B series, which is different on thickness as below:
►WO12864B : thickness 12.1mm (Max)
►WO12864B1 : thickness 6.0mm

ÇIZIM

Winstar WO12864B 128x64 COG LCD Modules
Data source ref:WO12864B-TFH#

AYRINTILAR

Arayüz Pin Fonksiyonlari

Pin No. Symbol Level TANIM
1 /CS1B I This is the chip select signal.
2 /RES I When RES is set to “L”, the setting are initialized.
3 A0 I This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.
4 /WR(R/W) I • When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.
5 /RD(E) I

• When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
• When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.

6~13 D0~D7 I/O Data bus line
14 VDD Power supply Power supply
15 VSS Power supply Ground
16 VOUT O DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD
17 CAP3P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
18 CAP1N O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal.
19 CAP1P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
20 CAP2P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal.
21 CAP2N O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal.
22~26 V4~V0 Power supply This is a multi-level power supply for the liquid crystal drive.
27 VR I Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
28 C86 I This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface
29 P/S I This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:
P/S Data/Command Data Read/Write Serial Clock
"H" A0 D0 to D7 /RD,/WR X
"L" A0 SI(D7) Write only SCL(D6)
When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM
30 NC - No connection.

Mekanik Veri

Kalem Ölçü Birim
Number of Dots 128 x 64
Modül ölçüleri 89.7 x 49.8 x 11.8 mm
Görüntüleme alanı 69.0 x 36.5 mm
Aktif alan 63.97 x 31.97 mm
Nokta boyutu 0.47 x 0.47 mm
Nokta sıklığı 0.5 x 0.5 mm
Duty 1/65 , 1/9 Bias
Backlight Tipi LED
IC ST7565P
Arayüz 6800/8080/4-Line SPI

Maksimum Değerler

Kalem Sembol Minumum Deger Tipik Deger Maksimum Deger Birim
Çalışma Sıcaklığı TOP -20 +70
Saklama Sıcaklığı TST -30 +80
Power Supply Voltage VDD -0.3 3.6 V
Power supply voltage (VDD standard) V0,VOUT -0.3 14.5 V
Power supply voltage (VDD standard) V1,V2,V3,V4 -0.3 V0+0.3 V

Elektronik Özellikleri

Kalem Sembol Condition Minumum Deger Tipik Deger Maksimum Deger Birim
Supply Voltage For Logic VDD-VSS 2.7 3.3 V
Supply Voltage For LCM V0-VSS Ta=-20℃
Ta=25℃
Ta=70℃
9.5
9.2
8.95
9.8
9.45
9.2
10.5
9.8
9.45
V
V
V
Input High Volt. VIH 0.8 VDD VDD V
Input Low Volt. VIL VSS 0.2VDD V
Output High Volt. VOH IOUT=-0.5mA 0.8VDD VDD V
Output Low Volt. VOL IOUT=0.5mA VSS 0.2VDD V
Supply Current(No include LED Backlight) IDD 0.6 2.0 mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd
go top
close

Gizliliğinize değer veriyoruz

"Tüm Çerezlere İzin Ver" seçeneğine tıklayarak, site gezinmesini geliştirmek, site kullanımını analiz etmek ve pazarlama ve performans çalışmalarımıza yardımcı olmak amacıyla cihazınıza çerezlerin kaydedilmesini kabul etmiş olursunuz. Bu konu hakkında daha fazla bilgiye politikamızda ulaşabilirsiniz. Gizlilik Politikası

Gizliliğinize değer veriyoruz

Winstar ve bazı üçüncü taraflar www.winstar.com.tw adresinde çerezler kullanmaktadır. Çerez türleri, amaçları ve ilgili üçüncü taraflar hakkındaki ayrıntılar aşağıda ve Çerez Politikamızda açıklanmaktadır. Web sitemizde en iyi deneyimi yaşamak için çerez kullanımına izin vermek amacıyla “Hepsine İzin Ver” düğmesine tıklayabilirsiniz. Ayrıca tercihlerinizi ayarlayabilir veya zorunlu olanlar haricindeki çerezleri reddedebilirsiniz.

Rıza tercihlerini yönet

Her zaman aktif
Gerekli Çerezler

Bu çerezler, web sitesinde gezinmenizi ve gizlilik tercihlerinizi ayarlamak, oturum açmak veya formları doldurmak gibi özellikleri kullanmanızı sağlamak için gereklidir.

Analitik Çerezler

“İstatistik çerezleri” olarak da bilinen bu çerezler, bir web sitesini nasıl kullandığınız hakkında bilgi toplar; örneğin, hangi sayfalara girdiğinizi ve hangi bağlantılara tıkladığınızı. Ayrıntılara bakın.