Home Prodotti Display LCD LCM COG WO12864B

Grafici LCM COG 128x64

Modello numero WO12864B

►LCM COG 128x64
►Tipo: grafico
►Struttura: COG
►Dimensione: 2.82 pollici
►128x64 a matrice di punti
►IC: ST7565P
►Alimentatore 3.3V
►1/65 duty cycle
►WO12864B: 12.1 millimetri di spessore
►WO12864B1: 6,0 millimetri di spessore
►Interfaccia : 6800/8080/SPI

Descrizione

There are two versions for WO12864B series, which is different on thickness as below:
►WO12864B : thickness 12.1mm (Max)
►WO12864B1 : thickness 6.0mm

DISEGNO

Winstar WO12864B 128x64 COG LCD Modules
Data source ref:WO12864B-TFH#

SPECIFICHE TECNICHE

Funzione dei Pin di Interfaccia

Pin No. Simbolo Level descrizione
1 /CS1B I This is the chip select signal.
2 /RES I When RES is set to “L”, the setting are initialized.
3 A0 I This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.
4 /WR(R/W) I • When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.
5 /RD(E) I

• When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
• When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.

6~13 D0~D7 I/O Data bus line
14 VDD Power supply Power supply
15 VSS Power supply Ground
16 VOUT O DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD
17 CAP3P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
18 CAP1N O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal.
19 CAP1P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
20 CAP2P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal.
21 CAP2N O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal.
22~26 V4~V0 Power supply This is a multi-level power supply for the liquid crystal drive.
27 VR I Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
28 C86 I This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface
29 P/S I This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:
P/S Data/Command Data Read/Write Serial Clock
"H" A0 D0 to D7 /RD,/WR X
"L" A0 SI(D7) Write only SCL(D6)
When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM
30 NC - No connection.

Dati meccanici

Articolo Dimensioni Unità
Number of Dots 128 x 64
Dimensione del modulo 89.7 x 49.8 x 11.8 mm
Area di visualizzazione 69.0 x 36.5 mm
Area attiva 63.97 x 31.97 mm
Dimensioni del Dot 0.47 x 0.47 mm
Passo del Dot 0.5 x 0.5 mm
Duty 1/65 , 1/9 Bias
Tipo di backlight LED
IC ST7565P
Interfaccia 6800/8080/4-Line SPI

Valori massimi assoluti

Articolo Simbolo Min Valore tipico Valore massimo Unità
Temperatura di lavoro TOP -20 +70
Temperatura di stock TST -30 +80
Power Supply Voltage VDD -0.3 3.6 V
Power supply voltage (VDD standard) V0,VOUT -0.3 14.5 V
Power supply voltage (VDD standard) V1,V2,V3,V4 -0.3 V0+0.3 V

Caratteristiche elettriche

Articolo Simbolo Condition Min Valore tipico Valore massimo Unità
Supply Voltage For Logic VDD-VSS 2.7 3.3 V
Supply Voltage For LCM V0-VSS Ta=-20℃
Ta=25℃
Ta=70℃
9.5
9.2
8.95
9.8
9.45
9.2
10.5
9.8
9.45
V
V
V
Input High Volt. VIH 0.8 VDD VDD V
Input Low Volt. VIL VSS 0.2VDD V
Output High Volt. VOH IOUT=-0.5mA 0.8VDD VDD V
Output Low Volt. VOL IOUT=0.5mA VSS 0.2VDD V
Supply Current(No include LED Backlight) IDD 0.6 2.0 mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd
go top
close

Valorizziamo la tua privacy

Facendo clic su "Consenti tutti i cookie", accetti la memorizzazione dei cookie sul tuo dispositivo per migliorare la navigazione del sito, analizzare l'utilizzo del sito e assistere nei nostri sforzi di marketing e prestazioni. Puoi trovare ulteriori informazioni su questo argomento nella nostra politica. Informativa sulla privacy

Valorizziamo la tua privacy

Winstar e alcune terze parti utilizzano i cookie su www.winstar.com.tw. I dettagli relativi ai tipi di cookie, al loro scopo e alle terze parti coinvolte sono descritti di seguito e nella nostra Informativa sui cookie. Fare clic su "Consenti tutti" per acconsentire all'uso dei cookie e ottenere la migliore esperienza possibile sui nostri siti web. Puoi anche impostare le tue preferenze o rifiutare i cookie (ad eccezione dei cookie strettamente necessari).

Gestisci le preferenze di consenso

Sempre attivo
Cookie essenziali

Questi cookie sono essenziali per permetterti di navigare nel sito web e utilizzare le sue funzionalità, come impostare le tue preferenze sulla privacy, effettuare il login o compilare moduli.

Cookie di analisi

Questi sono noti anche come "cookie statistici"; raccolgono informazioni su come utilizzi un sito web, come quali pagine hai visitato e quali link hai cliccato. Vedi dettagli.