Display LCD COG Gráfico de 128x64 - WO12864B

Display LCD COG Gráfico de 128x64

Model No. WO12864B

►LCD COG 128x64
►LCD Gráfico
►IC: ST7565P
►Alimentação 3,3V
►1/65 duty cycle
►WO12864B1 : espessura 12,1mm
►WO12864B1 : espessura 6,0mm
►Interface : 6800/8080/SPI

PDF DOWNLOAD

DEMO CODE ADD TO INQUIRY

PREV. BACK to LIST NEXT

Descrição

There are two versions for WO12864B series, which is different on thickness as below:
►WO12864B : thickness 12.1mm (Max)
►WO12864B1 : thickness 6.0mm

DRAWING

Data source ref:WO12864B-TFH#

SPECIFICATIONS

Função do pino de interface

Pin No.

Símbolo

Level

DESCRIÇÃO

/CS1B

This is the chip select signal.

/RES

When RES is set to “L”, the setting are initialized.

This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.

/WR(R/W)

• When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.

/RD(E)

• When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
• When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.

6~13

D0~D7

I/O

Data bus line

VDD

Power supply

VSS

Power supply

Ground

VOUT

DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD

CAP3P

DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.

CAP1N

DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal.

CAP1P

DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.

CAP2P

DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal.

CAP2N

DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal.

22~26

V4~V0

Power supply

This is a multi-level power supply for the liquid crystal drive.

Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.

C86

This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface

P/S

This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:

P/S	Data/Command	Data	Read/Write	Serial Clock
"H"	A0	D0 to D7	/RD,/WR	X
"L"	A0	SI(D7)	Write only	SCL(D6)

When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM

No connection.

Dados Mecânicos

Item	Dimensão	Unidade
Number of Dots	128 x 64	－
Dimensão do módulo	89.7 x 49.8 x 11.8	mm
View area	69.0 x 36.5	mm
Área ativa	63.97 x 31.97	mm
Tamanho do ponto	0.47 x 0.47	mm
Distância entre pontos	0.5 x 0.5	mm
Duty	1/65 , 1/9 Bias
Tipo de luz de fundo	LED
IC	ST7565P
Interface	6800/8080/4-Line SPI

Classificações Máximas Absolutas

Item	Símbolo	Min	Típico	Máximo	Unidade
Temperatura de operação	TOP	-20	－	+70	℃
Temperatura de armazenamento	TST	-30	－	+80	℃
Power Supply Voltage	VDD	-0.3	－	3.6	V
Power supply voltage (VDD standard)	V0,VOUT	-0.3	－	14.5	V
Power supply voltage (VDD standard)	V1,V2,V3,V4	-0.3	－	V0+0.3	V

Características Eletrônicas

Item	Símbolo	Condition	Min	Típico	Máximo	Unidade
Supply Voltage For Logic	VDD-VSS	－	2.7	－	3.3	V
Supply Voltage For LCM	V0-VSS	Ta=-20℃ Ta=25℃ Ta=70℃	9.5 9.2 8.95	9.8 9.45 9.2	10.5 9.8 9.45	V V V
Input High Volt.	VIH	－	0.8 VDD	－	VDD	V
Input Low Volt.	VIL	－	VSS	－	0.2VDD	V
Output High Volt.	VOH	IOUT=-0.5mA	0.8VDD	－	VDD	V
Output Low Volt.	VOL	IOUT=0.5mA	VSS	－	0.2VDD	V
Supply Current(No include LED Backlight)	IDD	－	－	0.6	2.0	mA