제품 COG LCD WO12864C2

128x64 COG LCD 디스플레이

모델 번호 WO12864C2

►128x64 COG LCD 디스플레이
►그래픽 LCD
►IC: ST7565P
►3.3V 전원 공급 장치
►1/64 듀티 사이클
►인터페이스 : 6800/8080/SPI

도면

Winstar Chip-on-Glass LCD Module 128x64 - WO12864C2
Data source ref:WO12864C2-TFH#

사양

인터페이스 핀 기능

Pin No. 기호 Level 설명
1 IRS I This terminal selects the resistors for the V0 voltage level adjustment.
IRS = “H”: Use the internal resistors
IRS = “L”: Do not use the internal resistors. The V0 voltage level is

 

regulated by an external resistive voltage divider attached to the VR terminal
2 /HPM I This is the power control terminal for the power supply circuit for liquid crystal drive.
/HPM = “H”: Normal mode
/HPM = “L”: High power mode (Default)
3 P/S I This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:
P/S Data/Command Data Read/Write Serial Clock
"H" A0 D0 to D7 /RD,/WR X
"L" A0 SI(D7) Write only SCL(D6)
When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM
4 C86 I This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface
5 VR I Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
IRS = “L” : the V0 voltage regulator internal resistors are not used.
IRS = “H” : the V0 voltage regulator internal resistors are used.
6~10 V0~V4 Power supply This is a multi-level power supply for the liquid crystal drive.
11 VRS Power supply This is the internal-output VREG power supply for the LCD power supply voltage regulator
12 CAP4+ O DC/DC voltage converter.
13 CAP2- O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal.
14 CAP2+ O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal.
15 CAP1+ O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
16 CAP1- O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal.
17 CAP3+ O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
18 CAP5+ O DC/DC voltage converter.
19 VOUT O DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD
20 VSS Power supply Ground
21 VDD Power supply Power supply
22~29 D7~D0 I/O Data bus line
30 /RD(E) I • When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
• When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.
31 /WR(R/W) I

• When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.

32 A0 I This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.
33 /RES I When RES is set to “L”, the setting are initialized.
34 /CS1 I This is the chip select signal.

기계적 데이터

항목 치수 단위
점의 수 128 x 64
모듈 치수 55.2 x 39.8 x 6.5 mm
보기 영역 45.2 x 27.0 mm
활성 영역 40.92 x 24.28 mm
도트 크기 0.28 x 0.34 mm
도트 피치 0.32 x 0.38 mm
듀티 1/65 , 1/9 Bias
역광 타입 LED
IC ST7565P
인터페이스 6800/8080/4-Line SPI

절대 최대 정격값

항목 기호 최소값 대표값 최대값 단위
작동 온도 TOP -20 +70
보관 온도 TST -30 +80
Power Supply Voltage VDD -0.3 3.6 V
Power supply voltage (VDD standard) V0,VOUT -0.3 14.5 V
Power supply voltage (VDD standard) V1,V2,V3,V4 -0.3 V0+0.3 V

전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage For Logic VDD-VSS 2.7 3.0 3.3 V
Supply Voltage For LCM V0-VSS Ta=-20℃
Ta=25℃
Ta=70℃

9.4

9.6

9.8
V
V
V
Input High Volt. VIH 0.8 VDD VDD V
Input Low Volt. VIL VSS 0.2VDD V
Output High Volt. VOH 0.8VDD VDD V
Output Low Volt. VOL VSS 0.2VDD V
Supply Current(No include LED Backlight) IDD VDD=3.0V 0.49 1.0 mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd
go top
close

우리는 귀하의 프라이버시를 소중히 여깁니다

"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책

우리는 귀하의 프라이버시를 소중히 여깁니다

Winstar와 일부 제3자는 www.winstar.com.tw에서 쿠키를 사용합니다. 쿠키의 종류, 목적 및 관련된 제3자에 대한 자세한 내용은 아래 및 당사의 쿠키 정책에 설명되어 있습니다. 웹사이트에서 최상의 경험을 얻으려면 "모두 허용"을 클릭하여 당사의 쿠키 사용에 동의해 주세요. 또한 선호 설정을 하거나 필수 쿠키를 제외한 쿠키를 거부할 수도 있습니다.

동의 설정 관리

항상 활성화
필수 쿠키

이 쿠키는 웹사이트를 탐색하고 개인 정보 설정, 로그인 또는 양식 작성과 같은 기능을 사용할 수 있도록 하는 데 필수적입니다.

분석 쿠키

“통계 쿠키”라고도 알려진 이러한 쿠키는 웹사이트 사용에 대한 정보를 수집합니다. 예를 들어 어떤 페이지를 방문했는지, 어떤 링크를 클릭했는지와 같은 정보입니다. 자세한 내용을 확인하세요.