Home Productos Pantalla LCD Pantalla LCD COG WO12864C2

Pantalla LCD Display 128x64

Modelo Nº WO12864C2

►COG LCD
►Tipo: Gráfico
►Estructura: COG
►Tamaño : 1.87 pulgada
►Matriz de puntos 122x64
►IC: ST7565P
►Fuente de alimentación de 3,3V
►1/64 duty cycle
►Interfaz : 6800/8080/SPI

DIBUJO

Winstar Chip-on-Glass LCD Module 128x64 - WO12864C2
Data source ref:WO12864C2-TFH#

ESPECIFICACIONES

Función interfaz Pin

Pin No. Símbolo Level Descripción
1 IRS I This terminal selects the resistors for the V0 voltage level adjustment.
IRS = “H”: Use the internal resistors
IRS = “L”: Do not use the internal resistors. The V0 voltage level is

 

regulated by an external resistive voltage divider attached to the VR terminal
2 /HPM I This is the power control terminal for the power supply circuit for liquid crystal drive.
/HPM = “H”: Normal mode
/HPM = “L”: High power mode (Default)
3 P/S I This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:
P/S Data/Command Data Read/Write Serial Clock
"H" A0 D0 to D7 /RD,/WR X
"L" A0 SI(D7) Write only SCL(D6)
When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM
4 C86 I This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface
5 VR I Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
IRS = “L” : the V0 voltage regulator internal resistors are not used.
IRS = “H” : the V0 voltage regulator internal resistors are used.
6~10 V0~V4 Power supply This is a multi-level power supply for the liquid crystal drive.
11 VRS Power supply This is the internal-output VREG power supply for the LCD power supply voltage regulator
12 CAP4+ O DC/DC voltage converter.
13 CAP2- O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal.
14 CAP2+ O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal.
15 CAP1+ O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
16 CAP1- O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal.
17 CAP3+ O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.
18 CAP5+ O DC/DC voltage converter.
19 VOUT O DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD
20 VSS Power supply Ground
21 VDD Power supply Power supply
22~29 D7~D0 I/O Data bus line
30 /RD(E) I • When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
• When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.
31 /WR(R/W) I

• When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.

32 A0 I This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.
33 /RES I When RES is set to “L”, the setting are initialized.
34 /CS1 I This is the chip select signal.

Datos mecánicos

Elemento Dimensión Unidad
Number of Dots 128 x 64
Dimensión del módulo 55.2 x 39.8 x 6.5 mm
Área de visión 45.2 x 27.0 mm
zona activa 40.92 x 24.28 mm
Tamaño del punto 0.28 x 0.34 mm
Distancia entre puntos 0.32 x 0.38 mm
Deber 1/65 , 1/9 Bias
Tipo de retroiluminación LED
IC ST7565P
interfaz 6800/8080/4-Line SPI

Valores noValor mín.ales máximos absolutos

Elemento Símbolo Valor mín. Valor típico Valor máx. Unidad
Temperatura de funcionamiento TOP -20 +70
Temperatura de almacenamiento TST -30 +80
Power Supply Voltage VDD -0.3 3.6 V
Power supply voltage (VDD standard) V0,VOUT -0.3 14.5 V
Power supply voltage (VDD standard) V1,V2,V3,V4 -0.3 V0+0.3 V

Características electrónicas

Elemento Símbolo Condition Valor mín. Valor típico Valor máx. Unidad
Supply Voltage For Logic VDD-VSS 2.7 3.0 3.3 V
Supply Voltage For LCM V0-VSS Ta=-20℃
Ta=25℃
Ta=70℃

9.4

9.6

9.8
V
V
V
Input High Volt. VIH 0.8 VDD VDD V
Input Low Volt. VIL VSS 0.2VDD V
Output High Volt. VOH 0.8VDD VDD V
Output Low Volt. VOL VSS 0.2VDD V
Supply Current(No include LED Backlight) IDD VDD=3.0V 0.49 1.0 mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd
go top
close

Valoramos tu privacidad

Al hacer clic en "Permitir todas las cookies", aceptas el almacenamiento de cookies en tu dispositivo para mejorar la navegación en el sitio, analizar el uso del sitio y ayudar en nuestros esfuerzos de marketing y rendimiento. Puedes encontrar más información sobre este tema en nuestra política. Política de privacidad

Valoramos tu privacidad

Winstar y ciertos terceros utilizan cookies en www.winstar.com.tw. Los detalles sobre los tipos de cookies, su propósito y las partes involucradas se describen a continuación y en nuestra Política de Cookies. Haga clic en “Permitir todos” para dar su consentimiento para el uso de cookies y tener la mejor experiencia posible en nuestros sitios web. También puede establecer sus preferencias o rechazar cookies (excepto las cookies estrictamente necesarias).

Gestionar preferencias de consentimiento

Siempre activo
Cookies esenciales

Estas cookies son esenciales para permitirte navegar por el sitio web y utilizar sus funciones, como establecer tus preferencias de privacidad, iniciar sesión o completar formularios.

Cookies de análisis

También conocidos como "cookies estadísticas", estas cookies recogen información sobre cómo utilizas un sitio web, como qué páginas has visitado y qué enlaces has clicado. Ver detalles.