Accueil Produits Afficheur TFT Module LCD TFT standard WF70BTIAHLNB0

N° de modèle WF70BTIAHLNB0

►Résolution d’écran: 1024×600
►Dimension: 7.0”
►Vue préférentielle 12h
►Interface: LVDS
►IC Part No. :ILI2511
►Carte de contrôle: NON
►Luminosité (Cd/m²): 450
►Cadre de maintien avec points de fixation: NON
►Dalle tactile: Avec dalle tactile capacitive (PCAP)
►PCAP Interface : USB (I2C available)

DESSIN

1024x600 Display, USB PCAP TFT Display 7 - WF70BTIAHLNB0 - Winstar Display

SPÉCIFICATIONS

Fonction PIN sur l'interface

1.LCM PIN Definition
Pin No. Symbole I/O Fonction
1 VCOM P Common Voltage
2 VDD P Digital circuit
3 VDD P Digital circuit
4 NC --- No connection
5 Reset I Global reset pin
6 STBYB I Standby mode, Normally pulled high
STBYB = “1”, normal operation
STBYB = “0”, timing controller, source driver will turn off, all output are High-Z
7 GND P Ground
8 RXIN0- I Negative LVDS differential data input
9 RXIN0+ I Positive LVDS differential data input
10 GND P Ground
11 RXIN1- I Negative LVDS differential data input
12 RXIN1+ I Positive LVDS differential data input
13 GND P Ground
14 RXIN2- I Negative LVDS differential data input
15 RXIN2+ I Positive LVDS differential data input
16 GND P Ground
17 RXCLKIN- I Negative LVDS differential clock input
18 RXCLKIN+ I Positive LVDS differential clock input
19 GND P Ground
20 RXIN3- I Negative LVDS differential data input
21 RXIN3+ I Positive LVDS differential data input
22 GND P Ground
23 NC --- No connection
24 NC --- No connection
25 GND P Ground
26 NC --- No connection
27 DIMO O Backlight CABC controller signal output
28 SELB I 6bit/8bit mode select    H:6bit / L:8bit
29 AVDD P Power for Analog Circuit
30 GND P Ground
31 LED- P LED Cathode
32 LED- P LED Cathode
33 L/R I Horizontal inversion
34 U/D I Vertical inversion
35 VGL P Negative power for TFT
36 GND P Ground
37 GND P Ground
38 VGH P Positive power for TFT
39 LED+ P LED Anode
40 LED+ P LED Anode

PCAP PIN Definition
Pin Symbole Fonction
1 USB_VSS System ground
2 USB_VDD 5V Power supply
3 USB_D+ Data +
4 USB_D- Data -
5 VSS System ground
6 SDA I2C data input and output
7 SCL I2C clock input
8 RST External Reset, Low is active
9 INT External interrupt to the host
10 VDDT 3.3 Power supply

Spécifications générales

Article Dimensions Unité
Dimension 7.0 pouces
Matrice de points 1024 × RGB × 600(TFT) points
Dimensions du module 202.0 (W) × 135.5 (H) × 8.73 (D) mm
Zone active 154.2144 × 85.92 mm
Pas des points 0.1506× 0.1432 mm
Type de LCD TFT, Blanc, Transmissif
Vue préférentielle 12 o'clock
Inversion de sens de l'échelle de gris 6 o'clock
Rapport d'aspect 16:9
Type de rétroéclairagee LED, Blanc
Interface LVDS
Dalle tactile PCAP
PCAP IC ILI2511
PCAP Interface USB (I2C available)
PCAP FW Version V 6. 0. 0. 0. 7.65. 0. 1
Surface Reflets

Valeurs nominales maximales absolues

Article Symbole Min Valeur type Max Unité
Température de fonctionnement TOP -20 +70
Température de stockage TST -30 +80

Caractéristiques électroniques

Typical Operation Conditions
Article Symbole Valeur Unité
Min Typ Max
Power voltage DVDD 3.0 3.3 3.6 V
AVDD 9.4 9.6 9.8 V
VGH 17 18 19 V
VGL -6.6 -6.0 -5.4 V
Supply Voltage For Touch
Logic
VDDT 2.8 3.3 V
Input signal voltage VCOM 3.1 3.3 3.6 V
Input logic high voltage VIH 0.7 DVDD - DVDD V
Input logic low voltage VIL 0 - 0.3 DVDD V
go top
close