Écran TFT MIPI IPS Haute Luminosité 10,1 pouces 1024x600

N° de modèle WF101JSYAHMNN0

►Dimension 10.1 pouces
►Résolution d’écran: 1024×600 points
►Vue préférentielle IPS
►Interface: 4-Lanes MIPI
►CI pilote : EK79007AD3 + EK73217BCGA
►Carte de contrôle: No
►Luminosité (Cd/m²): 1100
►Cadre de maintien avec points de fixation: NON
►Dalle tactile: Sans dalle tactile

Téléchargement PDF

DEMO CODE Ajouter à demande

PRÉC. Retour à la liste SUIVANT

Description

The WF101JSYAHMNN0 is a 10.1-inch TFT LCD module with IPS wide viewing angles, boasting a resolution of 1024×600 dots and a high brightness of 1100 cd/m2. It comes equipped with EK79007AD3 + EK73217BCGA driver ICs, supporting 4-Lanes MIPI interfaces.

With a Digital Power Supply Voltage For LCD (VDD) ranging from 1.71V to 1.89V and a typical value of 1.8V, this module features a glare surface and a 16:9 aspect ratio. It can reliably operate within temperatures ranging from -20 ℃ to +70 ℃, with storage temperatures spanning from -30 ℃ to +80 ℃.

DESSIN

10.1 inch 1024x600 High Brightness MIPI IPS TFT Display - WF101JSYAHMNN0

SPÉCIFICATIONS

Interface

TFT LCD Module

Pin No.	Symbole	Function
1	VLED+	LED Anode
2	VLED+	LED Anode
3	VGH	Positive power for TFT
4	VGL	Negative power for TFT
5	UPDN	Gate up or down scan control. UPDN = ”L”, STV2 output vertical start pulse and UD pin output logical “L” to Gate driver. (default) UPDN = ”H”, STV1 output vertical start pulse and UD pin output logical “H” to Gate driver
6	SHLR	Source right or left sequence control. SHLR = ”L“, shift left: last data = S1←S2←S3….......←S1536 = first data. SHLR = ”H“, shift right: first data = S1→S2→S3….....→S1536 = last data.(default)
7	VLED-	LED Cathode
8	VLED-	LED Cathode
9	AVDD	Analog power
10	GND	Digital ground
11	D3P	MIPI data input.
12	D3N	MIPI data input.
13	GND	Digital ground
14	D2P	MIPI data input.
15	D2N	MIPI data input.
16	GND	Digital ground
17	CLKP	MIPI clock input
18	CLKN	MIPI clock input
19	GND	Digital ground
20	D1P	MIPI data input.
21	D1N	MIPI data input.
22	GND	Digital ground
23	D0P	MIPI data input.
24	D0N	MIPI data input.
25	GND	Digital ground
26	STBYB	Standby mode. STBYB = ”H“,normal operation(default) STBYB = ”L”, timing controller, source driver will turn off, all output are GND.
27	RESET	Global reset pin. Active Low to enter Reset State. Normally pull high. Connecting with an RC reset circuit for stability.
28	VDD (1.8V)	Digital power
29	VDD (1.8V)	Digital power
30	VCOMI	Common voltage

Spécifications générales

Article	Dimensions	Unité
Screen Diagonal	10.1	pouce
Number of Pixels	1024 RGB x 600	points
Dimensions du module	235(W) x 143(H) x 5.05(D)	mm
Zone active	222.72 (H) x 125.28(V)	mm
Pixel pitch	0.2175(W) x 0.2088(H)	mm
Type de LCD	TFT, Noir, Transmissif
Interface	4-Lanes MIPI
CI pilote	EK79007AD3 + EK73217BCGA ou équivalent
Vue préférentielle	85/85/85/85
Rapport d'aspect	16:9
Type de rétroéclairage	LED, Blanc
Avec/sans dalle tactile	Sans dalle tactile (écran)
Surface	Anti-reflets

Valeurs nominales maximales absolues

Article	Symbole	Min	Typ	Max	Unité
Température de fonctionnement	TOP	-20	－	+70	℃
Température de stockage	TST	-30	－	+80	℃

Caractéristiques électroniques

Typical Operation Conditions (At Ta = 25 °C,)

Article	Symbole	Min	Typ	Max	Unité
Digital Power Supply Voltage For LCD	VDD	1.71	1.8	1.89	V
Analog Power Supply Voltage	AVDD	9.89	10.2	10.5	V
Gate On Power Supply Voltage	VGH	19.4	20	20.6	V
Gate Off Power Supply Voltage	VGL	-10.3	-10	-9.7	V
Common Power Supply Voltage	VCOMI	4	4.3	4.6	V