Pantalla TFT IPS 10.1 pulgada 1024x600 Con Panel Táctil Capacitivo Support HDMI Signal
Modelo Nº WF101JSYFHLHBV
►Tamaño: 10.1 pulgada
►Resolución : 1024x600 pontos
►Dirección de la vista: IPS
►Interfaz : Support HDMI Connector (Only DVI Signal)
►Controlador IC: TFP401
►Placa de control : Yes
►Brillo (cd/m2): 850
►Agujero del bastidor : No
►Pantalla táctil : Con panel táctil capacitivo (PCAP)
►Detect Point (Fingers) : 1 / 2 / Option
►Temperatura de funcionamiento : -20~+70℃
Descripción
WF101JSYFHLHBVes un módulo TFT-LCD de 2 una resolución de 1024x600 píxelesy una relación de aspecto de 16:9, que cuenta con pantalla táctil capacitiva proyectada. Este modelo está integrado con IC de controlador EK79001HN y EK73215BCGA eadmite interfaz de señal HDMI (solo para DVI). El panel táctil capacitivo está integrado con IC de controlador ILI2511 que admite interfaz USB con un punto de detección (admite el toque de 5 puntos).
Esta pantalla TFT-LCD se ofrece con un panel IPS que tiene las ventajas de un ángulo de visión más amplio a la izquierda (85 grados), a la derecha (85grados), arriba (85 grados) y abajo (85 grados) (valores típicos). Tiene un alto brillo, con un valor de 850 cd/㎡ y una relación de contraste (valor típico) de 800:1. Esta serie de módulo puede funcionar a temperaturas de -20 ℃ a +70 ℃ y su temperatura de almacenamiento oscila entre -30 ℃ y +80 ℃.
Simplemente puede usar esta pantalla TFT con su Raspberry Pi, o también como pantalla de PC con cualquier dispositivo que admita salida de señal HDMI.
DIBUJO
ESPECIFICACIONES
Especificaciones generales
Elemento | Dimensión | Unidad |
---|---|---|
Tamaño | 10.1 | pulgada |
Matriz de puntos | 1024 RGB x 600 | dots |
Dimensión del módulo | 235(W) x143(H) x 27.96(MAX)(D) | mm |
zona activa | 222.72 (H) x 125.28(V) | mm |
Distancia entre puntos | 0.2175(W) x 0.2088(H) | mm |
Tipo de LCD | TFT, Negro, Transmisivo | |
Dirección de la vis | 85/85/85/85 | |
Pixel Arrangement | RGB-STRIPE | |
Relación de aspecto | 16:9 | |
Controlador IC | EK79001HN + EK73215BCGA o equivalente | |
Tipo de retroiluminación | LED, Blanco | |
Interfaz (Logic) | Support HDMI Connector (Only DVI Signal) | |
PCAP IC | ILI2511 o equivalente | |
PCAP Interfaz | USB | |
Versión PCAP FW | V6.0.0.0.62.90.1.2 | |
Con o sin panel táctil | Con panel táctil capacitivo (PCAP) | |
Superficie | Deslumbramiento |
Valores nominales máximos absolutos
Elemento | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
---|---|---|---|---|---|
Temperatura de funcionamiento | TOP | -20 | - | +70 | ℃ |
Temperatura de almacenamiento | TST | -30 | - | +80 | ℃ |
Características electrónicas
Elemento | Símbolo | Condición | Valor mín. | Valor típico | Valor máx. | Unidad |
---|---|---|---|---|---|---|
Supply Voltage For LCM | VDD | - | 4.7 | 5 | 5.3 | V |
Supply Current For LCM | IDD | - | - | 1.7 | 2.6 | A |
LED life time | - | - | 50000 | - | - | Hr |
Función interfaz Pin
1.CON6
Pin No. | Símbolo | Función |
---|---|---|
1 | NC | No connection |
2 | 5V | Raspberry Pi:Power 5V |
3 | GPIO02 | Raspberry Pi:GPIO02 |
4 | 5V | Raspberry Pi:Power 5V |
5 | GPIO03 | Raspberry Pi:GPIO03 |
6 | GND | Raspberry Pi:GND |
7 | GPIO04 | Raspberry Pi:GPIO04 |
8 | GPIO14 | Raspberry Pi:GPIO14 |
9 | GND | Raspberry Pi:GND |
10 | GPIO15 | Raspberry Pi:GPIO15 |
11 | GPIO17 | Raspberry Pi:GPIO17 |
12 | BL-PWM (GPIO18) |
Backlight Enable ,Active_L (Raspberry Pi:GPIO18) |
13 | GPIO27 | Raspberry Pi:GPIO27 |
14 | GND | Raspberry Pi:GND |
15 | GPIO22 | Raspberry Pi:GPIO22 |
16 | GPIO23 | Raspberry Pi:GPIO23 |
17 | NC | No connection |
18 | GPIO24 | Raspberry Pi:GPIO24 |
19 | GPIO10 | Raspberry Pi:GPIO10 |
20 | GND | Raspberry Pi:GND |
21 | GPIO09 | Raspberry Pi:GPIO09 |
22 | GPIO25 | Raspberry Pi:GPIO25 |
23 | GPIO11 | Raspberry Pi:GPIO11 |
24 | GPIO08 | Raspberry Pi:GPIO08 |
25 | GND | Raspberry Pi:GND |
26 | GPIO07 | Raspberry Pi:GPIO07 |
27 | ID_SD | Raspberry Pi:ID_SD |
28 | ID_SC | Raspberry Pi:ID_SC |
29 | GPIO05 | Raspberry Pi:GPIO05 |
30 | GND | Raspberry Pi:GND |
31 | GPIO06 | Raspberry Pi:GPIO06 |
32 | GPIO12 | Raspberry Pi:GPIO12 |
33 | GPIO13 | Raspberry Pi:GPIO13 |
34 | GND | Raspberry Pi:GND |
35 | GPIO19 | Raspberry Pi:GPIO19 |
36 | GPIO16 | Raspberry Pi:GPIO16 |
37 | GPIO26 | Raspberry Pi:GPIO26 |
38 | GPIO20 | Raspberry Pi:GPIO20 |
39 | GND | Raspberry Pi:GND |
40 | GPIO21 | Raspberry Pi:GPIO21 |
2.CON5
Pin No. | Símbolo | Función |
---|---|---|
1 | 3.3V | TFT Module Power limit can only output 3.3V,100mA |
2 | 5V | Raspberry Pi:Power 5V |
3 | GPIO02 | Raspberry Pi:GPIO02 |
4 | 5V | Raspberry Pi:Power 5V |
5 | GPIO03 | Raspberry Pi:GPIO03 |
6 | GND | Raspberry Pi:GND |
7 | GPIO04 | Raspberry Pi:GPIO04 |
8 | GPIO14 | Raspberry Pi:GPIO14 |
9 | GND | Raspberry Pi:GND |
10 | GPIO15 | Raspberry Pi:GPIO15 |
11 | GPIO17 | Raspberry Pi:GPIO17 |
12 | BL-PWM (GPIO18) |
Backlight Enable ,Active_L (Raspberry Pi:GPIO18) |
13 | GPIO27 | Raspberry Pi:GPIO27 |
14 | GND | Raspberry Pi:GND |
15 | GPIO22 | Raspberry Pi:GPIO22 |
16 | GPIO23 | Raspberry Pi:GPIO23 |
17 | 3.3V | TFT Module Power limit can only output 3.3V,100mA |
18 | GPIO24 | Raspberry Pi:GPIO24 |
19 | GPIO10 | Raspberry Pi:GPIO10 |
20 | GND | Raspberry Pi:GND |
21 | GPIO09 | Raspberry Pi:GPIO09 |
22 | GPIO25 | Raspberry Pi:GPIO25 |
23 | GPIO11 | Raspberry Pi:GPIO11 |
24 | GPIO08 | Raspberry Pi:GPIO08 |
25 | GND | Raspberry Pi:GND |
26 | GPIO07 | Raspberry Pi:GPIO07 |
27 | ID_SD | Raspberry Pi:ID_SD |
28 | ID_SC | Raspberry Pi:ID_SC |
29 | GPIO05 | Raspberry Pi:GPIO05 |
30 | GND | Raspberry Pi:GND |
31 | GPIO06 | Raspberry Pi:GPIO06 |
32 | GPIO12 | Raspberry Pi:GPIO12 |
33 | GPIO13 | Raspberry Pi:GPIO13 |
34 | GND | Raspberry Pi:GND |
35 | GPIO19 | Raspberry Pi:GPIO19 |
36 | GPIO16 | Raspberry Pi:GPIO16 |
37 | GPIO26 | Raspberry Pi:GPIO26 |
38 | GPIO20 | Raspberry Pi:GPIO20 |
39 | GND | Raspberry Pi:GND |
40 | GPIO21 | Raspberry Pi:GPIO21 |
3.PCAP USB PIN Definition
Pin | Símbolo | Función |
---|---|---|
1 | 5V | Power Supply (5V) |
2 | D- | Data line - |
3 | D+ | Data line + |
4 | NC | No connection |
5 | GND | Power Ground |
4.DVI
Pin No. | Símbolo | I/O | Función |
---|---|---|---|
1 | Rx2+ | I | +LVDS Differential Data Input |
2 | GND | P | Ground |
3 | Rx2- | I | -LVDS Differential Data Input |
4 | Rx1+ | I | +LVDS Differential Data Input |
5 | GND | P | Ground |
6 | Rx1- | I | -LVDS Differential Data Input |
7 | Rx0+ | I | +LVDS Differential Data Input |
8 | GND | P | Ground |
9 | Rx0- | I | -LVDS Differential Data Input |
10 | RxC+ | I | +LVDS Differential Clock Input |
11 | GND | P | Ground |
12 | RxC- | I | -LVDS Differential Clock Input |
13-14 | NC | - | No connection |
15 | SCL | I/O | DDC(Data Display Channel) Clock |
16 | SDA | I/O | DDC(Data Display Channel) Data |
17 | GND | P | Ground |
18 | 5V | P | Power Supply |
19 | Detect | I/O | Hot plug detect |
5.Power-Jack
Pin No. | Símbolo | I/O | Función |
---|---|---|---|
1 | 5V | P | Power Supply (5V) |
2 | GND | P | Ground |
3 | NC | - | No connection |