Олед дисплей (Графические) 1.12", 6800 / 8080 / SPI / I2C интерфейсы, 128x128
Артикул. WEO128128G
►Тип: Графический
►Тип монтажа контроллера: COG
►Диагональ: 1.12 дюйма
►Разрешение: 128 x 128 точек
►IC:SH1107
►3V Power supply
►1/128 duty
►Интерфейс: 6800,8080,4-wire SPI,I2C
►Цвет дисплея: Белый / Желтый
Описание
WEO128128G – 1.12'' дюймовый графический COG OLED модуль с разрешением 128x128 пикселей и шлейфом для пайки. Данный дисплей сделан на базе контроллера IC SH1107 c поддержкой интерфейсов: параллельного 6800/8080, I2C и 4–х жильного SPI интерфейса. Напряжение питания модуля 3V(типичное значение), напряжение питания для дисплея @12V Vсс, а рабочий цикл 1/128. Значение тока при засвете 50% площади индикатора составляет 15mA для белого OLED свечения. WEO128128G может работать при температурах от –40°С до +80°С; а температура хранения – от –40°С до +85°С.
WEO128128G OLED – дисплей создан по технологии «chip–on–glass», что позволило сделать его очень тонким – всего 1,26 мм! Этот легкий, мощный и очень тонкий индикатор, который идеально подойдет для таких применений как: медицинские приборы, системы «умного дома», терминалы оплаты, Облачные/IoT системы, умные устройства, автомобилестроение, коммуникационные системы и т.д.
Чертеж
Data source ref:WEO128128GWAP3N00000
Технические характеристики
Функции контроллера контактного интерфейса
No. | Символы | Описание | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VPP | This is the most positive voltage supply pad of the chip. It should be supplied externally. |
|||||||||||||||
2 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
3 | VDD | Power supply for logic and input. | |||||||||||||||
4 | NC | Not connected. | |||||||||||||||
5 | IM1 | These are the MPU interface mode select pads.
|
|||||||||||||||
6 | IM2 | ||||||||||||||||
7 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625mA. | |||||||||||||||
8 | CS | This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled. | |||||||||||||||
9 | RES | This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. | |||||||||||||||
10 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
|||||||||||||||
11 | WR | This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When WR = “H”: Read. When WR = “L”: Write. |
|||||||||||||||
12 | E/RD | This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU. |
|||||||||||||||
13~20 | D0~D7 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance. When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). At this time, D2 to D7 are set to high impedance. |
|||||||||||||||
21 | GND | Ground | |||||||||||||||
22 | NC | Not connected. |
Механические характеристики
Наименование | Измерения | Единица |
---|---|---|
Разрешение | 128 × 128 | точек |
Габариты | 25.9 x 30.1 x 1.26 | mm |
Активная область | 20.076 x 20.076 | mm |
Размер пикселя | 0.137 x 0.137 | mm |
Шаг пикселя | 0.157 x 0.157 | mm |
Матрица | Пассивная матрица | |
Цвет дисплея | монохромные | |
Рабочий цикл | 1/128 Duty | |
IC | SH1107 | |
Интерфейс | 6800,8080,4-wire SPI,I2C | |
Диагональ | 1.12 дюйма |
Абсолютные максимальные значения
Параметр | Символы | Минимальный | Максимальный | Единица |
---|---|---|---|---|
Напряжение питания логических схем | VDD | -0.3 | 3.6 | V |
Напряжение питания дисплея | VPP | -0.3 | 17.0 | V |
Диапазон рабочих температур | TOP | -40 | +80 | °C |
Температура хранения | TSTG | -40 | +85 | °C |
Электронные характеристики
Наименование | Символы | Кондиция | Минимальный | Типичный | Максимальный | Единица |
---|---|---|---|---|---|---|
Напряжение питания логических схем | VDD | - | 1.65 | 3.0 | 3.3 | V |
Напряжение питания Display | VPP | - | 7.0 | 12.0 | 12.5 | V |
Высокое входное напряжение | VIH | - | 0.8×VDD | - | VDD | V |
Низкое входное напряжение | VIL | - | 0 | - | 0.2×VDD | V |
д высокого уровня | VOH | - | 0.8×VDD | - | VDD | V |
Выход низкого уровня | VOL | - | 0 | - | 0.2×VDD | V |
50% Check Board operating Current | IPP | VPP=12V | - | 15.0 | 25.0 | mA |
Search keyword: 128x128 oled, oled 128x128, 1.12 oled, 1.12" oled, 1.12дюйма oled, oled 1.12, oled 1.12"