설명
WF28JTYAJDNF0는 해상도가 240x320 픽셀, 밝기가 400 cd/m2이며 명암비가 800:1인 2.8인치 세로 방향 TFT 디스플레이 모듈입니다. 이 LCD 모듈은 예상 전용용성 터치 패널을 갖추고 있으며 MCU 또는 SPI 인터페이스를 지원하는 ILI9341V IC가 장착되어 있습니다. 모듈의 크기는 50.5 x 69.7 mm이며 활성 영역은 43.2 x 57.6 mm입니다. 공급 전압은 1.65V에서 3.3V까지입니다. 예상 전용용성 터치 패널은 I2C 인터페이스 및 단일 감지 지점을 지원하는 FT6336G IC와 통합되어 있습니다. 모듈은 -20°C에서 +70°C의 온도 범위에서 작동할 수 있으며 저장 온도는 -30°C에서 +80°C까지입니다.
WF28JTYAJDNF0는 IPS 기술을 사용하여 좌: 80 / 우: 80 / 상: 80 / 하: 80도 (평균값)의 넓은 시야각을 제공합니다. IPS 패널은 TFT 디스플레이에서 더 넓은 시야각, 정확하고 일관된 색상 재현, 우수한 화질, 정밀한 터치 성능 및 일관된 색온도를 제공합니다. IPS TFT-LCD 디스플레이의 다용도성은 소비자 전자제품, 의료 디스플레이 및 산업 제어 패널을 포함한 다양한 응용 분야에 적합합니다.
도면
사양
인터페이스 핀 기능
LCM PIN Definition
NO | 기호 | 기능 | I/O | ||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | P | ||||||||||||||||||||||||||||||||||||||||||||
2-6 | NC | No connection | - | ||||||||||||||||||||||||||||||||||||||||||||
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O | ||||||||||||||||||||||||||||||||||||||||||||
10 | CS | Chip select signal. | I | ||||||||||||||||||||||||||||||||||||||||||||
11 | D/CX(SCL) | (D/CX): This pin is used to select "Data or Command" in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
30 | RESET | (RESX)This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I | ||||||||||||||||||||||||||||||||||||||||||||
31 | IM0 | Select the MCU interface mode
MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
32 | IM1 | ||||||||||||||||||||||||||||||||||||||||||||||
33 | IM2 | ||||||||||||||||||||||||||||||||||||||||||||||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
35 | DB17 | ||||||||||||||||||||||||||||||||||||||||||||||
36 | LEDK | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
37 | LEDK | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
38 | LEDA | Anode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
40 | NC | Not used, open this pin | N |
PCAP PIN Definition
Pin | 기호 | 기능 |
---|---|---|
1 | VSS | Ground for analog circuit |
2 | VDDT | Power Supply : +3.3V |
3 | SCL | I2C clock input |
4 | NC | No connect |
5 | SDA | I2C data input and output |
6 | NC | No connect |
7 | /RST | External Reset, Low is active |
8 | NC | No connect |
9 | /INT | External interrupt to the host |
10 | VSS | Ground for analog circuit |
일반 사양
항목 | 치수 | 단위 |
---|---|---|
크기 (대각선) | 2.8 | 인치 |
도트 매트릭스 (해상도) | 240 x RGB x 320(TFT) | dots |
모듈 치수 | 50.5(W) x 69.7(H) x5.67(D) | mm |
활성 영역 (AA) | 43.2 x 57.6 | mm |
도트 피치 | 0.18 x 0.18 | mm |
LCD 유형 | TFT, 검은색, 투과성 | |
TFT 드라이버 IC | ILI9341V 또는 이와 동등한 | |
TFT 인터페이스 | MCU/SPI | |
시야각 | 80/80/80/80 | |
종횡비 | 3:4 | |
역광 타입 | LED,백색 | |
PCAP IC | FT6336G 또는 이와 동등한 | |
PCAP인터페이스 | I2C | |
PCAP FW | 0x11 | |
터치 패널 | 용량식 터치패널(스크린)이 있는 | |
표면 | 눈부심 |
절대 최대 정격값
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
작동 온도 | TOP | -20 | - | +70 | ℃ |
보관 온도 | TST | -30 | - | +80 | ℃ |
전기적 특성
Operating conditions
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage for digital | IOVCC | - | 1.65 | - | 3.3 | V |
Supply Voltage for analog | VCI | - | 2.5 | - | 3.3 | V |
Supply Voltage For Touch Logic | VDDT | - | 3.0 | 3.3 | 3.6 | V |
Power Supply for Current | ICC | IOVCC=VCI =VCC=3.0V |
- | 13 | 20 | mA |
LED driving conditions
Parameter | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
LED current | - | - | 80 | - | mA |
LED voltage | LEDA | 8.1 | 9.3 | 10.5 | V |
LED Life Time | - | 50000 | - | - | Hr |