首页 产品介绍 OLED显示屏 字符OLED显示屏 WEO002004C

20*4 SSD1331 字符OLED显示模块

型号 WEO002004C

►类型:点阵字符型
►结构:COG
►20字x4行
►IC:SSD1311
►3V/5V电源电压
►1/32 duty
►接口:6800, 8080, SPI, I2C
►发光颜色: 白色 / 黄色
►其它FPC选项请参阅最下方表格说明

产品叙述

WEO002004C OLED显示屏为COG结构的20字x4行的OLED模块 ,产品轻薄且高对比对广视角,低功耗。WEO002004C 内建 SSD1311 IC, 可支持 6800/8080 8-bit 并列接口 和 I2C, 4线 SPI 串列接口。建议客户可以使用华凌光电此款20x4字符型OLED模块 取代传统LCD模块,将产品升级为PMOLED显示屏。

  • 超快反应速度, +25℃时只需10 μsec
  • 超广视角- 可达175度
  • 轻薄- 自发光,无需背光
  • 超高亮度
  • 高对比- 10,000:1 以上
  • 超广温
  • 低耗电流- 减少CO2 排放量

WEO002004C可选接口:6800 OLED显示模块,8080 OLED显示模块,SPI OLED显示模块,I2C OLED显示模块


     可选 FPC

 

规格图

 6800 / 8080 /SPI / I2C 20x4 OLED Display -  WEO002004C Drawing

Data source ref: WEO002004CLPP5N00000

产品规格

Pin功能定义

Pin No. 符号 Pin 类型 说明
1 NC No connection
2 VSL P This is segment voltage (output low level) reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, connect with resistor and diode to ground (details depend on application).
3 VSS P Ground pin. It must be connected to external ground.
4 REGVDD I Internal VDD regulator selection pin in 5V I/O application mode.
When this pin is pulled HIGH, internal VDD regulator is enabled (5V I/O application).
When this pin is pulled LOW, internal VDD regulator is disabled (Low voltage I/O application).
5 SHLC I This pin is used to determine the Common output scanning direction.
COM scan direction
SHLC COM scan direction
1 COM0 to COM31 (Normal)
0 COM31 to COM0 (Reverse)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
6 SHLS I This pin is used to change the mapping between the display data column address and the Segment driver.
SEG scan direction
SHLS SEG direction
1 SEG0 to SEG99 (Normal)
0 SEG99 to SEG0 (Reverse)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
7 VDD P Power supply for core logic operation.
VDD can be supplied externally or regulated internally.
In LV IO application (internal VDD is disabled), this is a power input pin.
In 5V IO application (internal VDD is enabled), VDD is regulated internally from VDDIO.
A capacitor should be connected between VDD and VSS under all circumstances.
8 VDDIO P Low voltage power supply and power supply for interface logic level in both Low Voltage I/O and 5V I/O application. It should match with the MCU interface voltage level and must be connected to external source.
9 BS0 I MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.
Bus Interface selection
BS[2:0] Interface
000 Serial Interface
001 Invalid
010 I2C
011 Invalid
100 8-bit 6800 parallel
101 4-bit 6800 parallel
110 8-bit 8080 parallel
111 4-bit 8080 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
10 BS1
11 BS2
12 GPIO I/O It is a GPIO pin. Details refer to OLED command DCh.
13 CS# I This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
In I2C mode, this pin must be connected to VSS.
14 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
15 D/C# I This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When serial interface is selected, this pin must be connected to VSS.
16 R/W#(WR#) I This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E(RD#) I This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID and D2 will be the serial data output: SOD.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I This pin is the segment output current reference pin.
IREF is supplied externally.
A resistor should be connected between this pin and VSS to maintain current of around 15uA.
27 ROM0 I These pins are used to select Character ROM; select appropriate logic setting as described in the following table. ROM1 and ROM0 are pin select as shown in below table:
Character ROM selection
ROM1 ROM0 ROM
0 0 A
0 1 B
1 0 C
1 1 S/W selectable(3)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
28 ROM1
29 OPR0 I This pin is used to select the character number of character generator.
Character RAM selection
OPR1 OPR0 CGROM CGRAM
1 1 256 0
0 1 248 8
1 0 250 6
0 0 240 8

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
30 OPR1
31 VCOMH P COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
32 VCC P Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
33 NC No connection

规格说明

项目 尺寸 单位
字符数 20字x4行
模块尺寸 84.5 x 27.5 x 2.17 mm
检视区域 72.42 x 22.82 mm
有效区域 70.42 x 20.82 mm
点大小 0.57 x 0.57 mm
点间距 0.60 x 0.60 mm
字大小 2.97 x 4.77 mm
字间距 3.55 x 5.35 mm
LCD类型 OLED, 单色
Duty 1/32
IC SSD1311
界面 6800,8080,SPI,I2C
尺寸 2.89 寸

最大绝对额定值

项目 符号 最小值 最大值 单位
逻辑电源电压 VDD -0.3 VDDIO V
输入/输出针脚(Pin)电源 VDDIO -0.3 6 V
工作电压 VCC 0 16 V
工作温度 TOP -40 +80 °C
储存温度 TST -40 +85 °C
 

电气特性

DC 电气特性

项目 符号 条件 最小值 典型值 最大值 单位
逻辑电源电压 VDD Low Voltage I/O 2.4 3.0 3.3 V
5V I/O
(VDD as output)
V
输入/输出针脚(Pin)电源 VDDIO Low Voltage I/O 2.4 3.0 3.3 V
5V I/O 4.4 5.0 5.3 V
工作电压 VCC 8.0 10.0 10.5 V
8.0 12.0 12.5 V
输入高电压 VIH 0.8xVDDIO V
输入低电压 VIL 0.2xVDDIO V
输出高电压 VOH IOH=-0.5mA 0.9xVDDIO V
输出低电压 VOL IOL=0.5mA 0.1xVDDIO V
50%显示画面耗电流 ICC VCC=10V 19 29 mA
VCC=12V 23 35 mA

可选FPC :

图示 FPC长度 PIN pitch ZIF FPC or HOTBAR FPC 接口 FPC No. Create Date
FPC2070003111XXXXX00_WEO002004CLPP5N00000 35.2 31 0.7 BOTBAR FPC 6800,8080,SPI,I2C FPC2070003111XXXXX00 20120921
FPC2005003421XXXXX00_WEO002004CLPP5N00001 31 34 0.5 ZIF FPC 6800,8080,SPI,I2C FPC2005003421XXXXX00 20151223

Search keyword: oled 20x4, 20x4 oled

go top
close