首页 产品介绍 OLED显示屏 图形 OLED 显示屏 WEO025664A-ZIF

2.08寸, 256x64 OLED模块 (ZIF FPC)

型号 WEO025664A-ZIF

►类型:点阵图形
►结构:COG + ZIF FPC
►尺寸:2.08寸
►256x64点阵
►内置控制器SSD1362
►3V电源电压
►1/64 duty
►接口:6800, 8080, SPI, I2C
►发光颜色: 白色 / 黄色 / 支持灰度

产品叙述

WEO025664A-ZIF是一款2.08寸绘图型COG OLED显示器模块,分辨率256x64 pixels。此款模块内置SSD1362 驱动 IC,模块操作支持 6800/8080 8-bit 并列接口,I2C与3线及4线SPI接口,支持4 bits 灰阶模式,3V电压驱动,1/64 duty,以棋盘格50%画素点亮画面测试,VCC用12V点亮时耗电流15mA。此2.08寸COG结构的 WEO025664A-ZIF模块工作温度是-40℃至 80℃,储存温度-40℃至 85℃。

WEO025664A-ZIF是COG超薄化结构的OLED显示器,自发光无需背光非常轻薄,低耗电流,非常适用于智能家电、量测仪器、可携带式装置、智能医疗产品、个人健康守护追踪装置等产品。

规格图

2.08 OLED Display Module 256×64 -  WEO025664A-ZIF -Winstar Display

产品规格

Pin功能定义

No. 符号 功能
1 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VP This pin is the segment pre-charge voltage reference pin.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
4 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
5 VDD Power supply for core logic operation.
VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.
A capacitor should be connected between VDD and VSS under all circumstances.
6 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
7 IREF This pin is the segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA.
When internal IREF is used, this pin should be kept NC.
8 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
9 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
10 VSS Ground pin. It must be connected to external ground.
11 VSS Ground pin. It must be connected to external ground.
12 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
13 BS0 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1, BS0 are pin select.
BS[2:0] Interface
000 4 line SPI
001 3 line SPI
110 8-bit 8080 parallel
100 8-bit 6800 parallel
010 I2C
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
14 BS1
16 BS2
15 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
17 CS This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS is pulled LOW (active LOW).
In I2C mode, this pin must be connected to VSS.
18 RES This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
19 D/C This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
20 R/W This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
21 RD This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
22 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
23 D1
24 D2
25 D3
26 D4
26 D5
28 D6
29 D7
30 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
31 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

规格说明

项目 规格 单位
分辨率 256 x 64 Dots
模块尺寸 60.5 x 19.0 x 1.61 mm
有效区域 51.18 x 12.78 mm
像素大小 0.18 x 0.18 mm
像素间距 0.2 x 0.2 mm
显示模式 被动矩阵
显示颜色 单色
驱动方式 1/64 Duty
灰阶 4 Bits
IC SSD1362
接口 3线和4线 SPI, I2C, 6800, 8080
尺寸 2.08 寸

最大绝对额定值

参数 符号 最小值 最大值 单位
工作电源电压 VCI -0.5 5.5 V
逻辑电源电压 VDD -0.5 2.75 V
显示电源电压 VCC -0.5 21 V
工作温度 TOP -40 80 °C
储存温度 TSTG -40 85 °C

电气特性

DC电气特性

项目 符号 条件 最小值 典型值 最大值 单位
逻辑电源电压 VCI 2.8 3.0 3.3 V
逻辑电源电压 VCC 11.5 12 12.5 V
输入高电压 VIH 0.8×VCI VCI V
输入高电压 VIL VSS 0.2×VCI V
输出高电压 VOH 0.9×VCI VCI V
输出低电压 VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=12V 15 30 mA
go top
close