Strona główna Produkty Wyświetlacz OLED Graficzne Wyświetlacz OLED WEO012864AK

2.7", 128x64, SPI Wyświetlacz OLED graficzne

Numer modelu WEO012864AK

►Typ: graficzny
►Struktura: COG
►Rozmiar: 2.7"
►128 x 64 matryca punktowa
►IC:CH1116
►zasilanie 3V
►wypełnienie 1/64
►interfejs: 6800,8080,4-wire SPI,I2C
►Kolor wyświetlacza: biały / żółto
►MOQ: 150 K. Możesz wybrać WEO012864AM jako zamiennik WEO012864AK.

Opis

Rysunek

2.7 inch OLED, 128x64 SPI OLED Display - WEO012864AK
Data source ref:WEO012864AKWPP3N00G00

Specyfikacja

Funkcja pinów interfejsu

No. Symbol Funkcja
1 NC(VSS) No connection
2 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
3 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
4 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
5~12 D7~D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
13 E/RD# This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD# = “H”: Enable.
When RD# = “L”: Disable.
14 WR#
(R/W#)
This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W#= “H”: Read.
When R/W#= “L”: Write.
15 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
16 RES# This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level.
17 CS# This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled.
18 NC No connection
19 IM2 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
20 IM1
21 VDD1 Power supply input
22~28 NC No connection
29 VSS Ground.
30 NC(VSS) No connection


Dane mechaniczne

Rzecz Wymiar Jednostka
Matryca punktowa 128 × 64 dots
Wymiary modułu 73.0 × 41.86 × 2.01 mm
Obszar aktywny 61.41 × 30.69 mm
Wielkość piksela 0.45 × 0.45 mm
Raster pomiędzy pikselami 0.48 × 0.48 mm
Tryb wyświetlania matryca
Kolor wyświetlacza Monochromatyczny
Drive Duty 1/64 Duty
IC CH1116
Interfejs 6800,8080,4-Wire SPI,I2C
Rozmiar (Przekątna) 2.7 calowy

Bezwzględne oceny maksymalne

Parameter Symbol Minimalna wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VCC 0 14.5 V
Temperatura pracy TOP -40 +80 °C
Temperatura przechowywania TSTG -40 +85 °C

Parametry elektryczne

Rzecz Symbol Stan Minimalna wartość  Rodzaj działalności Maksymalna wartość Jednostka
Supply Voltage for Logic VDD1 1.65 3.0 3.3 V
Supply Voltage for Display VPP 6.4 13.0 13.5 V
High Level Input VIH 0.8×VDD1 VDD1 V
Low Level Input VIL VSS 0.2×VDD1 V
High Level Output VOH 0.8×VDD1 VDD1 V
Low Level Output VOL VSS 0.2×VDD1 V
Display 50% Pixel on IPP VPP =13V 15 30 mA

 

Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7" oled, 2.7 inch oled, oled 2.7, oled 2.7"

go top
close