128x64 액정 모듈, LCD 디스플레이

모델 번호 WO12864D2

►128*64 COG LCD 디스플레이
►그래픽 LCD
►IC: ST7565P
►3.3V 전원 공급 장치
►1/64 듀티 사이클
►인터페이스 : 6800/8080/SPI

PDF 다운로드

데모 코드 조회에 추가

이전 목록으로 돌아가기 다음

도면

Data source ref: WO12864D2-TFH#

사양

인터페이스 핀 기능

Pin No.	기호	설명
1	/CS1	This is the chip select signal. When /CS1 = “L” , then the chip select becomes active, and data/command I/O is enabled.
2	/RES	When /RES is set to “L” , the settings are initialized.
3	A0	This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or a command. A0 = “H”: Indicates that D0 to D7 are display data. A0 = “L”: Indicates that D0 to D7 are control data.
4	/WR(R/W)	When connected to an 8080 MPU, this is active LOW. (R/W) This terminal connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W = “H”: Read. When R/W = “L”: Write.
5	/RD(E)	When connected to an 8080 MPU, this is active LOW. (E) This pin is connected to the /RD signal of the 8080 MPU, and the ST7565P series data bus is in an output status when this signal is “L”. When connected to a 6800 Series MPU, this is active HIGH. This is the 6800 Series MPU enable clock input terminal.
6	DB0	This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data Bus.
7	DB1
8	DB2
9	DB3
10	DB4
11	DB5
12	DB6
13	DB7
14	VDD	Shared with the MPU power supply terminal VDD. ( 3.3 V )
15	VSS	This is a 0V terminal connected to the system GND.
16	VOUT	DC/DC voltage converter. Connect a capacitor between this terminal and VSS.
17	CAP5+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
18	CAP3+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
19	CAP1-	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1+ terminal.
20	CAP1+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
21	CAP2+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2- terminal.
22	CAP2-	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2+ terminal.
23	CAP4+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2- terminal.
24	VRS	This is the externally-input VREG power supply for the LCD power supply voltage regulator.
25	V4	This is a multi-level power supply for the liquid crystal drive. The voltage Supply applied is determined by the liquid crystal cell, and is changed through the use of a resistive voltage divided or through changing the impedance using an op. amp. Voltage levels are determined based on Vss, and must maintain the relative magnitudes shown below. V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧Vss When the power supply turns ON, the internal power supply circuits produce the V1 to V4 voltages shown below. The voltage settings are selected using the LCD bias set command.
26	V3
27	V2
28	V1
29	V0
30	VR	Output voltage regulator terminal. Provides the voltage between VDD and V5 through a resistive voltage divider. IRS = “L” : the V5 voltage regulator internal resistors are not used . IRS = “H” : the V5 voltage regulator internal resistors are used .
31	C86	This is the MPU interface switch terminal. C86 = “H”: 6800 Series MPU interface. C86 = “L”: 8080 MPU interface.
32	P/S	This is the parallel data input/serial data input switch terminal. P/S = “H”: Parallel data input. P/S = “L”: Serial data input. The following applies depending on the P/S status: When P/S = “L”, D0 to D5 may be “H”, “L” or Open. RD (E) and WR (R/W) are fixed to either “H” or “L”. With serial data input, It is impossible read data from RAM .
33	/HPM	This is the power control terminal for the power supply circuit for liquid crystal drive. HPM = “H”: Normal mode HPM = “L”: High power mode
34	IRS	This terminal selects the resistors for the V5 voltage level adjustment. IRS = “H”: Use the internal resistors IRS = “L”: Do not use the internal resistors. The V5 voltage level is regulated by an external resistive voltage divider attached to the VR terminal

일반 사양

항목	치수	단위
도트 매트릭스 (해상도)	128 x 64 dots	－
모듈 치수	90.0 x 52.8 x 6.6	mm
보기 영역	70.7 x 38.8	mm
활성 영역	66.52 x 33.24	mm
도트 크기	0.48 x0.48	mm
도트 피치	0.52 x 0.52	mm
듀티	1/64 , 1/9 Bias
역광 타입	LED
IC	ST7565P
인터페이스	6800/8080/4-Line SPI

절대 최대 정격값

항목	기호	최소값	대표값	최대값	단위
작동 온도	TOP	-20	－	+70	℃
보관 온도	TST	-30	－	+80	℃
Power Supply Voltage	VDD	-0.3	－	3.6	V
Power supply voltage (VDD standard)	V0, VOUT	-0.3	－	14.5	V
Power supply voltage (VDD standard)	V1, V2, V3, V4	-0.3	－	V0+0.3	V

전기적 특성

항목	기호	조건	최소값	대표값	최대값	단위
Supply Voltage For Logic	VDD-VSS	－	2.7	3.0	3.3	V
Supply Voltage For LCM	V0-VSS	Ta=-20℃ Ta=25℃ Ta=70℃	10.0 9.8 9.6	10.2 10.0 9.8	10.4 10.2 10.0	V V V
Input High Volt.	VIH	－	0.8 VDD	－	VDD	V
Input Low Volt.	VIL	－	Vss	－	0.2 VDD	V
Output High Volt.	VOH	－	0.8 VDD	－	VDD	V
Output Low Volt.	VOL	－	Vss	－	0.2VDD	V
Supply Current (LED backlight is not included)	IDD	VDD=3.0V		0.6	1	mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd