Accueil Produits Afficheur TFT LCD TFT IPS WF35UTYAIMNG0

LCD TFT IPS MIPI 320x240, 3.5" Avec dalle tactile capacitive

N° de modèle WF35UTYAIMNG0

►Dimension: 3.5"
►Résolution d’écran: 320×480 points
►Vue préférentielle IPS
►Interface: 1-Lane MIPI
►IC: ILI9488
►Carte de contrôle: NON
►Luminosité (Cd/m²): 500
►Holding frame with fixing points: NON
►Dalle tactile: Avec dalle tactile capacitive (PCAP)
►Detect Point : 5 Fingers

DESSIN

3.5 inch Portrait 320x480 MIPI IPS TFT LCD Module with PCAP - WF35UTYAIMNG0

SPÉCIFICATIONS

Interface

LCM PIN Definition

NO Symbole Fonction I/O
1 VCI A supply voltage to the analog circuit. Connect to an external power supply of 2.5 ~ 3.3V.
Connect to a stabilizing capacitor between VCI and GND.
P
2 IOVCC A supply voltage to the digital circuit. Connect to an external power supply of 1.65 ~ 3.3V. P
3 RESET Reset input signal
Initialize the chip with a low input. Be sure to execute a power-on
reset after supplying power.
I
4 GND Ground I
5 MIPI_CLK_P Positive polarity of low voltage differential clock signal Leave the pin open when not in use. I
6 MIPI_CLK_N Negative polarity of low voltage differential clock signal
Leave the pin open when not in use
I
7 GND Ground I
8 MIPI_DATA_P Positive polarity of low voltage differential data signal
Leave the pin open when not in use.
I
9 MIPI_DATA_N Negative polarity of low voltage differential data signal
Leave the pin open when not in use.
I
10 GND Ground I
11 VLED+ Anode of LED backlight.  
12 VLED- Cathode of LED backlight  

 

PCAP PIN Definition

Pin Symbole Fonction
1 VSS Connect to system ground.
2 VDDT Power Supply
3 SCL I2C clock input
4 NC No connect
5 SDA I2C data input and output
6 NC No connect
7 RST External Reset, Low is active
8 NC No connect
9 INT External interrupt to the host
10 VSS Connect to system ground.

Spécifications générales

Article Dimensions Unité
Dimension 3.5 pouce
Matrice de points 320 × RGB × 480(TFT) points
Dimensions du module 68.7 (W) × 95.6 (H) × 4.61(D) mm
Zone active 48.96 × 73.44 mm
Pas des points 0.153 × 0.153 mm
Type de LCD TFT, Noir, Transmissif
Vue préférentielle 80/80/80/80
Rapport d'aspect Portrait
CI pilote ILI9488 ou equivalent
Interface 1-Lane MIPI
Type de rétroéclairage LED, Blanc
PCAP Driver IC GT911  ou équivalent
PCAP Interface I2C
FW Version 0x95
PCAP Résolution 320*480
Avec/sans dalle tactile Avec dalle tactile capacitive
Surface Reflets

Valeurs nominales maximales absolues

Article Symbole Valeur min Valeur type Valeur max Unité
Température de fonctionnement TOP -20 70
Température de stockage TST -30 80

Caractéristiques électroniques

Article Symbole État Valeur min Valeur type Valeur max Unité
Supply Voltage for digital IOVCC 1.8/2.8 3.3 V
Supply Voltage for analog VCI 2.8 3.3 V
Power Supply for Current ICC IOVCC=VCI
=VCC=3.3V
13.6 mA
go top
close