N° de modèle WEO012864ANX
►Type: Graphique
►Structure: COG
►Dimension: 1.33 pouces
►Matrice de points 128x64
►IC：SSD1309
►Alimentation 3V
►1/64 duty
►Interface: 6800, 8080, SPI, I2C
►Couleur d'affichage: Jaune et Vert (Couleur Double)
Le WEO012864ANX est un module OLED de 1,33 pouces avec une résolution de 128x64 pixels et un affichage bi-couleur (Jaune + Vert) OLED. Cet affichage OLED jaune et vert OLED est conçu pour des applications nécessitant un contraste élevé et une faible consommation d'énergie, ce qui le rend idéal pour les dispositifs médicaux, les systèmes de contrôle industriels et les dispositifs portables. Équipé du contrôleur SSD1309 IC, il prend en charge des options d'interface flexibles, y compris 6800, 8080, SPI et I2C, garantissant une intégration facile dans les systèmes.
Data source ref: WEO012864ANXAP3N00000
| Article | Dimensions | Unité |
|---|---|---|
| Matrice de points | 128 × 64 Dots | － |
| Dimensions du module | 33.5 × 27.08 × 1.26 | mm |
| Zone active | 28.52 × 18.33 | mm |
| Taille des points | 0.203 × 0.258 | mm |
| Pas des points | 0.223 × 0.278 | mm |
| Mode d'affichage | Matrice passive | |
| Couleur d'affichage | Jaune et Vert (Couleur Double) | |
| Drive Duty | 1/64 Duty | |
| IC | SSD1309 | |
| Interface | 6800,8080,4-Wire SPI,I2C | |
| Diagonale | 1.33 pouces | |
| Paramètre | Symbole | Valeur min | Valeur max | Unité |
|---|---|---|---|---|
| Tension d'alimentation pour la logique | VDD | -0.3 | 4 | V |
| Tension d'alimentation pour l'affichage | VCC | 0 | 17 | V |
| Température de fonctionnement | TOP | -40 | +80 | °C |
| Température de stockage | TSTG | -40 | +85 | °C |
| Article | Symbole | État | Valeur min | Valeur type | Valeur max | Unité |
|---|---|---|---|---|---|---|
| Tension d'alimentation pour la logique | VDD | － | 1.65 | 3.0 | 3.5 | V |
| Tension d'alimentation pour l'affichage | VCC | － | 7.0 | 12.0 | 12.5 | V |
| Entrée Haute Tension | VIH | － | 0.8×VDD | － | － | V |
| Entrée Basse Tension | VIL | － | － | － | 0.2×VDD | V |
| Sortie Haute Tension | VOH | － | 0.9×VDD | － | － | V |
| Sortie Basse Tension | VOL | － | － | － | 0.1×VDD | V |
| Affichage 50 % des pixels allumés | ICC | VCC=12V | － | 8.0 | 12.0 | mA |
| No. | Symbole | Fonction | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | ESD_GND | It should be connected to ground. | |||||||||||||||
| 2 | VLSS | This is an analog ground pin | |||||||||||||||
| 3 | VSS | Ground. | |||||||||||||||
| 4 | NC | No connection | |||||||||||||||
| 5 | VDD | Power supply pin for core logic operation | |||||||||||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
| 7 | BS2 | ||||||||||||||||
| 8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
| 9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
| 10 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
| 11 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 12 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 13-20 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
| 21 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
| 22 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
| 23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
| 24 | ESD_GND | It should be connected to ground. |
En cliquant sur "Autoriser tous les cookies", vous acceptez le stockage de cookies sur votre appareil pour améliorer la navigation sur le site, analyser l'utilisation du site et aider dans nos efforts de marketing et de performance. Vous pouvez trouver plus d'informations à ce sujet dans notre politique. Politique de confidentialité