Pantalla TFT IPS 4.3" Con panel táctil capacitivo (used for Arduino)
Modelo Nº WF43WTYBEDSG0
►WF43WTYBEDSG0 : Built-in storage device (FLASH)
►WF43WTYBEDSG0#000 : Control Signal 5V; Without built-in storage device (FLASH); Support SD connector, Pin CON1~CON4 are used for Arduino Uno Rev3
►Tamaño: 4.3 pulgada
►Resolución :480×272 puntos
►Dirección de la vista: IPS
►Interfaz: SPI/QSPI
►Controlador IC: BT815
►Placa de control : Yes
►Brillo(cd/m²): 400
►Agujero del bastidor: Yes
►Pantalla táctil : Con panel táctil capacitivo (PCAP)
►Detect Point : 5 Fingers
►Temperatura de funcionamiento : -20~+70°C
DIBUJO
►WF43WTYBEDSG0# Spec Download ►WF43WTYBEDSG0#000 Spec Download
Data source ref: WF43WTYBEDSG0
ESPECIFICACIONES
Función interfaz Pin
LCM PIN Definition(CON5)
| Pin | Símbolo | I/O | Función |
|---|---|---|---|
| 1 | VDD | P | 3.3V power supply input |
| 2 | GND | P | Ground |
| 3 | SCK | I | SPI clock input |
| 4 | MISO | O | SPI Single mode: SPI MISO output SPI Dual/Quad mode: SPI data line 1 |
| 5 | MOSI | I | SPI Single mode: SPI MOSI input SPI Dual/Quad mode: SPI data line 0 |
| 6 | CS | I | SPI slave select input |
| 7 | INT | OD/O | Interrupt to host, open drain output(default) or push-pull output, active low |
| 8 | PD_N | I | Chip power down mode control input, active low. Connect to MCU GPIO for power management or hardware reset function |
| 9 | GPIO2 | I/O | General purpose IO 2 |
| 10 | GPIO3 | I/O | General purpose IO 3 |
| 11 | IO2 | I/O | SPI Single/Dual mode: General purpose IO 0 SPI Quad mode: SPI data line 2 |
| 12 | IO3 | I/O | SPI Single/Dual mode: General purpose IO 1 SPI Quad mode: SPI data line 3 |
| 13 | CSCL | I | Connect to I2C SCL pin of the CTP(ILI2130) |
| 14 | CSDA | I/O | Connect to I2C SDA pin of the CTP(ILI2130) |
| 15 | CRST | I | Connect to reset pin of the CTP(ILI2130) |
| 16 | CINT | O | Connect to interrupt pin of the CTP(ILI2130) |
| 17 | VLED | P | 5V power supply input |
| 18 | VLED | P | 5V power supply input |
| 19 | GND | P | Ground |
| 20 | GND | P | Ground |
Especificaciones generales
| Item | Dimension | Unit |
|---|---|---|
| Tamaño (Diagonal) | 4.3 | pulgada |
| Matriz de puntos (Resolución) | 480 x RGB x 272(TFT) | puntos |
| Dimensión del módulo | 123.5 (W) x 67.2 (H) x 14.73(D)(MAX) | mm |
| zona activa | 95.04 x 53.856 | mm |
| Distancia entre puntos | 0.198(H) x 0.198(V) | mm |
| Tipo de LCD | TFT, Negro, Transmisivo | |
| Dirección de la vista | 80/80/80/80 | |
| Relación de aspecto | 16:9 | |
| Tipo de retroiluminación | LED, Blanco | |
| TFT Controlador IC | BT816 | |
| TFT Interfaz | SPI/QSPI | |
| PCAP FW Versión | 0x07.0x00.0x00.0x00.0x01.0x0C.0x11.0x43 | |
| PCAP IC | ILI2130o equivalente | |
| PCAP Interfaz | I2C | |
| PCAP Resolución | 16384*16384 | |
| Superficie | Pantalla antirreflectante | |
Valores nominales máximos absolutos
| Elemento | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
|---|---|---|---|---|---|
| Temperatura de funcionamiento | TOP | -20 | － | +70 | ℃ |
| Temperatura de almacenamiento | TST | -30 | － | +80 | ℃ |
Características electrónicas
| Elemento | Símbolo | Condición | Valor mín. | Valor típico | Valor máx. | Unidad |
|---|---|---|---|---|---|---|
| Supply Voltage For VDD | VDD | － | 3.1 | 3.3 | 3.5 | V |
| Supply Current For VDD | IDD | VDD=3.3V | － | 100 | 150 | mA |
| Supply Voltage For VLED | VLED | － | 4.5 | 5 | 5.5 | V |
| Supply Current For VLED | ILED | VLED=+5V | － | 200 | 300 | mA |
