Home Productos Pantalla OLED Pantalla OLED Gráfico WEO012864AB
Módulos OLED Color dual 0.96 pulgada, 128x64 - WEO012864ABX
Módulos OLED Color dual 0.96 pulgada, 128x64 - WEO012864ABX
Módulos OLED Color dual 0.96 pulgada, 128x64 - WEO012864ABX

Módulos OLED Color dual 0.96 pulgada, 128x64

Modelo Nº WEO012864AB

►Tipo : Gráfico
►Estructura : COG
►Tamaño : 0.96 pulgada
►Matriz de puntos 128 x 64
►IC：SSD1315
►Fuente de alimentación de 3V
►1/64 duty
►Interfaz : 6800, 8080, SPI, I2C
►Color de la pantall: Color dual (have MOQ)

PREV. VOLVER A LA LISTA SIGUIENTE

Descripción

 

DIBUJO

0.96 inch 128x64 2 Color OLED Display Module - WEO012864ABX

Data source of: WEO012864ABXPP3N0Y000

ESPECIFICACIONES

Función interfaz Pin

No. Símbolo Función
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2P C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2N
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
7 NC NC
8 VSS This is a ground pin.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
  BS0 BS1 BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX Parallel 0 0 1
8-bit 80XX Parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
When internal IREF is used, this pin should be kept NC.
27 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)		 The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

Datos mecánicos

Elemento Valor estándar Unidad
Matriz de puntos 128 × 64 Dots －
Dimensión del módulo 24.7 × 16.59 × 1.26 mm
zona activa 21.74 × 11.20 mm
Tamaño del punto 0.15 × 0.15 mm
Distancia entre puntos 0.17 × 0.17 mm
Modo de visualización Matriz pasiva
Color de la pantalla Color dual (Amarillo / Azul cielo)
Drive Duty 1/64 Duty
IC SSD1315
Interfaz 6800,8080,SPI,I2C
Tamaño (Diagonal) 0.96 pulgada

Valores nominales máximos absolutos

Parameter Símbolo Valor mín. Valor máx. Unidad
Supply Voltage for Logic VDD 0 4 V
Charge Pump Regulator Supply Voltage VBAT -0.3 6.0 V
Supply Voltage for Display VCC 0 18.0 V
Temperatura de funcionamiento TOP -30 +70 °C
Temperatura de almacenamiento TSTG -30 +70 °C

Características electrónicas

DC Características electrónicas

Elemento Símbolo Condición Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic VDD － 1.65 3.0 3.3 V
Supply Voltage for Display
(Supplied Externally)		 VCC － 7.5 8.0 8.5 V
Charge Pump Regulator Supply Voltage VBAT － 3.0 3.5 4.2 V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump
VCC		 － 7.0 7.5 － V
Input High Volt. VIH － 0.8×VDD － VDD V
Input Low Volt. VIL － 0 － 0.2×VDD V
Output High Volt. VOH － 0.9×VDD － VDD V
Output Low Volt. VOL － 0 － 0.1×VDD V
Operating Current for VCC (Display 50% Pixel on)
(VCC Supplied Externally)		 ICC VCC =8V － 5.0 7.5 mA
Display 50% Pixel on
(VCC Generated by Internal DC/DC)		 IBAT VBAT=3.5V － 15 22.5 mA

Search keyword: 128x64 oled, oled 128x64, 0.96 oled, 0.96" oled, 0.96 inch oled, oled 0.96"

go top
close