Pantalla LCD Electrónica COG 128x128 (ST75161 IC)
Modelo Nº WO128128B
►LCD COG
►LCD Gráficos
►128×128 puntos
►IC: ST75161
►Fuente de alimentación de 3.3V
►1/128 DUTY , 1/12 BIAS
►Interfaz :6800/8080/SPI/I2C
DIBUJO
Data source ref： WO128128B-TFH#
ESPECIFICACIONES
Función interfaz Pin
| Pin No. | Símbolo | Descripción |
|---|---|---|
| 1 | ESD GND | ESD Ground |
| 2 | VG | VG is the power of SEG-drivers. |
| 3 | V0 | Positive operating voltage of COM-drivers. |
| 4 | XV0 | Negative operating voltage of COM-drivers. |
| 5 | CA1P | DC/DC voltage converter |
| 6 | CA1N | |
| 7 | VDD | Power supply |
| 8 | VSS | Ground |
| 9 | COMSCN | Set scan direction of COM. |
| 10 | IF2 | These pins select interface operation mode. |
| 11 | IF1 | |
| 12 | IF0 | |
| 13 | CSB | Chip select input pin. |
| 14 | A0 | It determines whether the access is related to data or command. |
| 15 | ERD | Read / Write execution control pin. |
| 16 | RWR | Read / Write execution control pin. |
| 17-24 | RSTB | Hardware reset input pin |
| 25 | ERD | When using 8-bit parallel interface: 8080 or 6800 mode:8 bit bi-directional data bus When using serial interface : 4-line SPI or 3-line SPI mode D[7:4] : fix to “H” by VDD1. D[3:1] : serial input/output data (SDA). D[0] : serial input clock (SCL). D1 to D3 must be connected together (SDA) When using serial interface : I2C interface D[7] : SA[1], I2C slave address bit. Must be connected to VDD1 or VSS1. D[6] : SA[0], I2C slave address bit. Must be connected to VDD1 or VSS1. D[5:4] : fix to “H” by VDD1. D[3:2] : SDA_OUT, serial data and acknowledge output for the I2C interface. D[1] : SDA_IN, serial input data D[0] : SCL, serial input clock . D1 to D3 must be connected together (SDA) CSB must be fixed to “L” by VSS1. |
| 26 | A | Anode input for LED backlight. |
| 27 | K | Cathode input for LED backlight |
| 28 | ESD GND | ESD Ground |
Especificaciones generales
| Elemento | Dimensión | Unidad |
|---|---|---|
| Matriz de puntos (Resolución) | 128 x 128 | － |
| Dimensión del módulo | 68.0 x 72.0 x 6.5 | mm |
| Área de visión | 62.0 x 62.0 | mm |
| zona activa | 55.01 x 55.01 | mm |
| Tamaño del punto | 0.4 x 0.4 | mm |
| Distancia entre puntos | 0.43 x 0.43 | mm |
| Deber | 1/128 DUTY,1/12 BIAS | |
| Tipo de retroiluminación | LED | |
| IC | ST75161 | |
| Interfaz | 6800/8080/3/4-Line SPI/I2C | |
Valores nominales máximos absolutos
| Elemento | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
|---|---|---|---|---|---|
| Temperatura de funcionamiento | TOP | -20 | - | +70 | ℃ |
| Temperatura de almacenamiento | TST | -30 | - | +80 | ℃ |
| Voltaje de la fuente de alimentación | VDD | -0.3 | - | 4.0 | V |
| Tensión de alimentación LCD | V0-XV0 | -0.3 | - | 19 | V |
| Voltaje de entrada | VIN | -0.3 | - | VDD+0.3 | V |
Características electrónicas
| Elemento | Símbolo | Condición | Valor mín. | Valor típico | Valor máx. | Unidad |
|---|---|---|---|---|---|---|
| Voltaje de suministro para lógica | VDD-VSS | - | 3.0 | 3.3 | 3.6 | V |
| Voltaje de suministro para LCD | VOP | Ta=-20℃ Ta=25℃ Ta=70℃ |
－ 14.8 － |
－ 15.1 － |
－ 15.4 － |
V V V |
| Entrada de alto voltaje. | VIH | - | 0.7 VDD | - | VDD | V |
| Entrada de bajo voltaje. | VIL | - | Vss | - | 0.3 VDD | V |
| Salida de alto voltaje. | VOH | - | 0.8 VDD | - | VDD | V |
| Salida de bajo voltaje. | VOL | - | Vss | - | 0.2 VDD | V |
| Corriente de suministro | IDD | VDD=3.3V | - | - | 2.5 | mA |
