Startseite Produkte TFT-LCDs TFT IPS Bildschirm WF24LTYAJDNN0

2,4 zoll IPS Bildschirm

Modellnummer WF24LTYAJDNN0

►Größe: 2,4 Zoll
►Auflösung: 240 x 320 Punkten
►Betrachtungsrichtung: IPS
►Schnittstelle: MCU, SPI
►Integrierter Controller: ILI9341V
►Steuerplatine: Nein
►Helligkeit (cd/m²): 500
►Durchsteckrahmen: Nein
►Touchscreen: ohne Touchscreen

Zeichnung

2.4" IPS Color TFT Module - WF24LTYAJDNN0 - Winstar Display

Technische Daten

Schnittstelle Pin-Funktion

NO Symbol Funktion I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(1.65 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to VDDI or VSS.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to VDDI level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to VDDI level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
30 RESET This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode

MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at VDDI or VSS.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDI(SDA) When IM[3] : Low, Serial in/out signal.
When IM[3] : High, Serial input signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at VDDI or VSS.
I/O
40 SDO Serial output signal.
The data is outputted on the falling edge of the SCL signal.
If not used, open this pin
O

Allgemeine Spezifikationen

Artikel Ausmaß Einheit
Größe (Diagonale) 2,4 Zoll
Punktmatrix (Auflösung) 240 × RGB × 320(TFT) Punkte
Abmaße der modul 42,72(W) × 60,26(H) × 2,8(D) mm
Aktiver Bereich 36,72 × 48,96 mm
Punktabstand 0.153 × 0,153 mm
LCD-Typ TFT, Schwarz, Transmissiv
Controller IC ILI9341V  oder gleichwertig
Blickwinkel 80/80/80/80
Seitenverhältnis Portrait
Backlight-Typ LED, Weiß
Touchscreen ohne Touchscreen
Oberfläche Glanz

absolute Grenzwerte

Artikel Symbol Mindestwert typischer Wert Maximalwert Einheit
Betriebstemperatur TOP -20 +70
Lagertemperatur TST -30 +80

elektrische Eigenschaften

Artikel Symbol Mindestwert typischer Wert Maximalwert Einheit
Supply Voltage For Analog VCI 2.5 3.3 V
Supply Voltage For Logic IOVCC 2.5 3.3 V
Supply Current For LCM ICI 6 9 mA
go top
close