3.12" дюймовый графический (256х64) COG OLED с платой и емкостной сенсорной тач панелью
Артикул. WEN025664B-CTP
►Тип: Графический
►Тип монтажа контроллера: COF+FR+PCB
►Диагональ: 3.12 дюйма
►Разрешение: 256×64 точек
►IC:SSD1322
►3V power supply
►1/64 duty cycle
►Интерфейс: 6800, 8080, SPI
►Емкостная сенсорная панель(CTP)
►1 точка касания
►Цвет дисплея: Белый / Желтый / Небесно голубой / Зеленый
►Инверсия
Описание
WEN025664B-CTP – это 3.12" дюймовый графический OLED дисплей с платой, с емкостной сенсорной тач панелью и крепёжной рамкой. Разрешение данного индикатора составляет 256x64 точки и сделан на базе контроллера IC SSD1322 c поддержкой интерфейсов: параллельного 6800/8080 8-Бит, I2C и четырехжильного SPI интерфейса. Шкала поддержки серого 16-бит (4-бит) Напряжение питания модуля 3.3V (типичное значение 3V), а рабочий цикл 1/64; значение тока при засвете 50% площади индикатора составляет 150mA @3VDD (типичное значение). Встроенный контроллер IC емкостной сенсорной панели –FT6336U с поддержкой I2C интерфейса. Распознавание касания 1 пальца, без поддержки мультитач. Дисплей имеет глянцевое покрытие. Индикатор имеет печатную плату на модуле, которая подходит для клиентов, использующих проводное соединение; заказчикам не нужно разрабатывать дополнительную печатную плату. Кроме того, мы интегрировали схему VCC на печатную плату, чтобы упростить работу с питанием индикатора.
OLED дисплей WEN025664B-CTP с емкостной сенсорной панелью идеально подходит для применения в таких областях как: “умный дом”, POS системы, Облачных/IoT системах, умных устройствах, автомобилестроении, коммуникационных системах, медицинских устройствах и т.д.
Данный дисплей может работать при температурах от -20°С до +70°С; а температура хранения - от -30°С до +80°С.
Кроме того, панели OLED с такими же размерами предлагают различные альтернативы:- Серия WEX025664B без металлической рамы, ПКБ и сенсорного экрана.
- Серия WEX025664B-CTP без металлической рамы, ПКБ и с емкостным сенсорным экраном.
- Серия WEN025664B с металлической рамой и ПКБ.
Чертеж
Data source ref: WEN025664BWPP3D00000
Технические характеристики
Функции контроллера контактного интерфейса
Pin Number | Символы | I/O | Описание | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | P | Ground. | ||||||||||
2 | VDD | P | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
3 | N.C. | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
4 | D/C# | I | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
5 | R/W# (WR#) |
I | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
6 | E/RD# | I | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
7~14 | DB0 | I/O | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
||||||||||
DB1 | |||||||||||||
DB2 | |||||||||||||
DB3 | |||||||||||||
DB4 | |||||||||||||
DB5 | |||||||||||||
DB6 | |||||||||||||
DB7 | |||||||||||||
15 | NC | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
16 | RES# | I | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
17 | CS# | I | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
18 | NC | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
19 | BS1 | I | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDD |
||||||||||
20 | BS0 | ||||||||||||
21 | TP_SCK | I | I2C clock input | ||||||||||
22 | TP_SDA | I | I2C data input and output | ||||||||||
23 | TP_INT | I | External interrupt to the host | ||||||||||
24 | TP_RST | I | External Reset, Low is active |
Механические характеристики
Наименование | Измерения | Единица |
---|---|---|
Разрешение | 256 x 64 точек | - |
Габариты | 89.2 × 44.0 × 7.98 | mm |
Активная область | 76.78 × 19.18 | mm |
Размер пикселя | 0.278 × 0.278 | mm |
Шаг пикселя | 0.3 × 0.3 | mm |
Матрица | Пассивная | |
Цвет дисплея | монохромные | |
Рабочий цикл | 1/64 Duty | |
Шкала серого | 4 bits | |
OLED IC | SSD1322 (COF) | |
OLED Интерфейс | 6800, 8080, SPI | |
Диагональ | 3.12 дюйма | |
CTP IC | FT6336U | |
точка обнаружения | 1 | |
CTP Интерфейс | I2C | |
Поверхность | Глянцевая |
Абсолютные максимальные значения
Параметр | Символы | Минимальный | Максимальный | Единица |
---|---|---|---|---|
Supply Voltage for Display | VDD | -0.3 | 4 | V |
Диапазон рабочих температур | TOP | -20 | +70 | °C |
Температура хранения | TSTG | -30 | +80 | °C |
Электронные характеристики
DC Электронные характеристики
Наименование | Символы | Кондиция | Минимальный | Типичный | Максимальный | Единица |
---|---|---|---|---|---|---|
Напряжение питания логических схем | VDD | - | 2.8 | 3.0 | 3.3 | V |
Вход высокого уровня | VIH | - | 0.8×VDD | - | VDD | V |
Вход низкого уровня | VIL | - | 0 | - | 0.2×VDD | V |
Выход высокого уровня | VOH | - | 0.9×VDD | - | VDD | V |
Выход низкого уровня | VOL | - | 0 | - | 0.1×VDD | V |
50% Check Board operating Current | IDD | VDD =3V | - | 150 | 300 | mA |
Search keyword: 256x64 oled, oled 256x64, 3.12 oled, 3.12" oled, 3.12 дюйма oled, oled 3.12"