128x32, Graficzne OLED 1.71"
Numer modelu WEO012832P
►Typ: graficzny
►Struktura: COG
►Rozmiar: 1.71"
►128 x 32 matryca punktowa
►IC：CH1115
►zasilanie 3V
►wypełnienie 1/32
►Interfejs: SPI, I2C
►Kolor wyświetlacza: biały / żółto
Opis
Rysunek
Data source ref: WEO012832PWAP3N00000
Specyfikacja
Funkcja pinów interfejsu
| No. | Symbol | Funkcja | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | ESD_GND | ESD Ground pin | ||||||||||||
| 2 | VPP | OLED panel power supply. | ||||||||||||
| 3 | VSS | This is a ground pin. | ||||||||||||
| 4 | VSS | This is a ground pin. | ||||||||||||
| 5 | VDD | Power Supply for Logic | ||||||||||||
| 6 | __ CS |
This pad is the chip select input. When /CS = “L”, then the chip select becomes active, and data/command I/O is enabled. | ||||||||||||
| 7 | ___ RES |
This is a reset signal input pad. When /RES is set to “L”, the settings are initialized. The reset operation is performed by the /RES signal level. | ||||||||||||
| 8 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
||||||||||||
| 9 | SCL | The serial clock input pad | ||||||||||||
| 10 | SI/SDA | The serial data input pad | ||||||||||||
| 11 | NC | Dummy Pin | ||||||||||||
| 12 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75μA. | ||||||||||||
| 13 | VCOMH | The pin is for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||||
| 14 | VPP | OLED panel power supply. | ||||||||||||
| 15 | IM0 | These are the MPU interface mode select pads.
|
||||||||||||
| 16 | IM1 | |||||||||||||
| 17 | VSS | This is a ground pin. | ||||||||||||
| 18 | ESD_GND | ESD Ground pin |
Dane mechaniczne
| Rzecz | Wymiar | Jednostka |
|---|---|---|
| Matryca punktowa | 128 × 32 | Dots |
| Wymiary modułu | 50.50 × 15.75 × 2.01 | mm |
| Obszar aktywny | 42.22 × 10.54 | mm |
| Wielkość piksela | 0.308 × 0.308 | mm |
| Raster pomiędzy pikselami | 0.33 × 0.33 | mm |
| Tryb wyświetlania | matryca | |
| Kolor wyświetlacza | Monochromatyczny | |
| Drive Duty | 1/32 Duty | |
| IC | CH1115 | |
| Interfejs | SPI, I2C | |
| Rozmiar | 1.71 cale | |
Bezwzględne oceny maksymalne
| Parameter | Symbol | Minimalna wartość | Maksymalna wartość | Jednostka |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | 3.6 | V |
| Supply Voltage for Display | VPP | -0.3 | 14.5 | V |
| Temperatura pracy | TOP | -40 | +80 | °C |
| Temperatura przechowywania | TSTG | -40 | +85 | °C |
Parametry elektryczne
| Rzecz | Symbol | Stan | Minimalna wartość | Typowa wartość | Maksymalna wartość | Jednostka |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 1.65 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VPP | － | 6.4 | 12.0 | 12.5 | V |
| High Level Input | VIH | － | 0.8×VDD | － | VDD | V |
| Low Level Input | VIL | － | VSS | － | 0.2×VDD | V |
| High Level Output | VOH | － | 0.8×VDD | － | VDD | V |
| Low Level Output | VOL | － | VSS | － | 0.2×VDD | V |
| Display 50% Pixel on | IPP | VPP=12V | － | 5 | 10 | mA |
Search keyword: 128x32 oled, oled 128x32, 1.71 oled, 1.71" oled, 1.71 cale oled, oled 1.71, oled 1.71"
