4,3 pouces 480x272 pour Affichage TFT Haute Luminosité Signal HDMI avec RTP
N° de modèle WF43WSYFEDHTV
►Dimension 4.3 pouces
►Résolution d’écran: 480×272 points
►Vue préférentielle 80/80/80/80
►Interface: Support HDMI Connector (Only DVI Signal)
►Contrôleur IC: TFP401
►Carte de contrôle: Yes
►Luminosité (Cd/m²): 700
►Cadre de maintien avec points de fixation: NON
►Dalle tactile: Avec dalle tactile résistive
►Température d’utilisation: -20~+70℃
Description
WF43WSYFEDHTV is a 4.3-inch High Brightness TFT LCD with a Resistive Touch Panel (RTP). The module features a control board with HDMI signal interface support (DVI only) and 40-pin GPIO connector, allowing developers to use it with Raspberry Pi (Raspberry Pi) effortlessly. Meanwhile, the 4 screw holes on the control board make it easy to mount. WF43WSYFEDHTV is built-in with controller TFP401, and it adopts an IPS panel providing wide viewing angles of Left: 80 / Right: 80 / Up: 80 / Down: 80 degrees (typical value). The display's brightness is 700 nits (typical value), and its resolution is 480×272 dots. This TFT LCD uses an anti-glare glass surface with a 16:9 aspect ratio. It can operate at temperatures from -20℃ to +70℃, and its storage temperatures are from -30℃ to +80℃.
DESSIN
SPÉCIFICATIONS
Spécifications générales
Article | Dimensions | Unité |
---|---|---|
Dimension | 4.3 | pouce |
Matrice de points | 480 × RGB × 272(TFT) | points |
Dimensions du module | 105.5(W) × 84.2(H) × 23.23(D) | mm |
Zone active | 95.04 ×53.856 | mm |
Pas des points | 0.198 × 0.198 | mm |
Type de LCD | TFT, Noir, Transmissif | |
Vue préférentielle | 80/80/80/80 (IPS) | |
Rapport d'aspect | 16:9 | |
Contrôleur IC | TFP401 | |
Interface | HDMI(only for DVI) | |
Type de rétroéclairage | LED, Blanc | |
RTP Interface | USB | |
Avec/sans dalle tactile | Avec dalle tactile résistive(USB) | |
Surface | Anti-reflets |
Valeurs nominales maximales absolues
Article | Symbole | Valeur min | Valeur type | Valeur max | Unité |
---|---|---|---|---|---|
Température de fonctionnement | TOP | -20 | - | +70 | ℃ |
Température de stockage | TST | -30 | - | +80 | ℃ |
Caractéristiques électroniques
Operating conditionsArticle | Symbole | État | Valeur min | Valeur type | Valeur max | Unité |
---|---|---|---|---|---|---|
Supply Voltage For LCM | VDD | - | - | 5.0 | - | V |
Supply Current For LCM | IDD | - | - | 1,000 | 1500 | mA |
LED life time | - | - | - | 50,000 | - | Hr |
Fonction PIN sur l'interface
1. LCM PIN Definition(CON4)
Pin | Symbole | Fonction | Remark |
---|---|---|---|
1 | NC | No connector | |
2 | 5V | Raspberry Pi:Power 5V | |
3 | GPIO02 | Raspberry Pi:GPIO02 | |
4 | 5V | Raspberry Pi:Power 5V | |
5 | GPIO03 | Raspberry Pi:GPIO03 | |
6 | GND | Raspberry Pi:GND | |
7 | GPIO04 | Raspberry Pi:GPIO04 | |
8 | GPIO14 | Raspberry Pi:GPIO14 | |
9 | GND | Raspberry Pi:GND | |
10 | GPIO15 | Raspberry Pi:GPIO15 | |
11 | GPIO17 | Raspberry Pi:GPIO17 | |
12 | GPIO18 (PWM_BL) |
Raspberry Pi:GPIO18 (PWM adjusts the backlight brightness) | Note2 |
13 | GPIO27 | Raspberry Pi:GPIO27 | |
14 | GND | Raspberry Pi:GND | |
15 | GPIO22 | Raspberry Pi:GPIO22 | |
16 | GPIO23 | Raspberry Pi:GPIO23 | |
17 | NC | No connector | |
18 | GPIO24 | Raspberry Pi:GPIO24 | |
19 | GPIO10 | Raspberry Pi:GPIO10 | |
20 | GND | Raspberry Pi:GND | |
21 | GPIO09 | Raspberry Pi:GPIO09 | |
22 | GPIO25 | Raspberry Pi:GPIO25 | |
23 | GPIO11 | Raspberry Pi:GPIO11 | |
24 | GPIO08 | Raspberry Pi:GPIO08 | |
25 | GND | Raspberry Pi:GND | |
26 | GPIO07 | Raspberry Pi:GPIO07 | |
27 | ID_SD | Raspberry Pi:ID_SD | |
28 | ID_SC | Raspberry Pi:ID_SC | |
29 | GPIO05 | Raspberry Pi:GPIO05 | |
30 | GND | Raspberry Pi:GND | |
31 | GPIO06 | Raspberry Pi:GPIO06 | |
32 | GPIO12 | Raspberry Pi:GPIO12 | |
33 | GPIO13 | Raspberry Pi:GPIO13 | |
34 | GND | Raspberry Pi:GND | |
35 | GPIO19 | Raspberry Pi:GPIO19 | |
36 | GPIO16 | Raspberry Pi:GPIO16 | |
37 | GPIO26 | Raspberry Pi:GPIO26 | |
38 | GPIO20 | Raspberry Pi:GPIO20 | |
39 | GND | Raspberry Pi:GND | |
40 | GPIO21 | Raspberry Pi:GPIO21 |
2. LCM PIN Definition(CON5)
Pin | Symbole | Fonction | Remark |
---|---|---|---|
1 | 3.3V | TFT Module Power limit can only output 3.3V,100mA | Note1 |
2 | 5V | Raspberry Pi:Power 5V | |
3 | GPIO02 | Raspberry Pi:GPIO02 | |
4 | 5V | Raspberry Pi:Power 5V | |
5 | GPIO03 | Raspberry Pi:GPIO03 | |
6 | GND | Raspberry Pi:GND | |
7 | GPIO04 | Raspberry Pi:GPIO04 | |
8 | GPIO14 | Raspberry Pi:GPIO14 | |
9 | GND | Raspberry Pi:GND | |
10 | GPIO15 | Raspberry Pi:GPIO15 | |
11 | GPIO17 | Raspberry Pi:GPIO17 | |
12 | GPIO18 (PWM_BL) |
Raspberry Pi:GPIO18 (PWM adjusts the backlight brightness) | Note2 |
13 | GPIO27 | Raspberry Pi:GPIO27 | |
14 | GND | Raspberry Pi:GND | |
15 | GPIO22 | Raspberry Pi:GPIO22 | |
16 | GPIO23 | Raspberry Pi:GPIO23 | |
17 | 3.3V | TFT Module Power limit can only output 3.3V,100mA | Note1 |
18 | GPIO24 | Raspberry Pi:GPIO24 | |
19 | GPIO10 | Raspberry Pi:GPIO10 | |
20 | GND | Raspberry Pi:GND | |
21 | GPIO09 | Raspberry Pi:GPIO09 | |
22 | GPIO25 | Raspberry Pi:GPIO25 | |
23 | GPIO11 | Raspberry Pi:GPIO11 | |
24 | GPIO08 | Raspberry Pi:GPIO08 | |
25 | GND | Raspberry Pi:GND | |
26 | GPIO07 | Raspberry Pi:GPIO07 | |
27 | ID_SD | Raspberry Pi:ID_SD | |
28 | ID_SC | Raspberry Pi:ID_SC | |
29 | GPIO05 | Raspberry Pi:GPIO05 | |
30 | GND | Raspberry Pi:GND | |
31 | GPIO06 | Raspberry Pi:GPIO06 | |
32 | GPIO12 | Raspberry Pi:GPIO12 | |
33 | GPIO13 | Raspberry Pi:GPIO13 | |
34 | GND | Raspberry Pi:GND | |
35 | GPIO19 | Raspberry Pi:GPIO19 | |
36 | GPIO16 | Raspberry Pi:GPIO16 | |
37 | GPIO26 | Raspberry Pi:GPIO26 | |
38 | GPIO20 | Raspberry Pi:GPIO20 | |
39 | GND | Raspberry Pi:GND | |
40 | GPIO21 | Raspberry Pi:GPIO21 |
Note1: The 3.3V supply current is limited; please pay special attention to use
Note2:PWM dimming frequency is about 100Hz
3. HDMI (only for DVI)
Pin No. | Symbole | I/O | Fonction | Remark |
---|---|---|---|---|
1 | Rx2+ | I | +LVDS Differential Data Input | |
2 | GND | P | Ground | |
3 | Rx2- | I | -LVDS Differential Data Input | |
4 | Rx1+ | I | +LVDS Differential Data Input | |
5 | GND | P | Ground | |
6 | Rx1- | I | -LVDS Differential Data Input | |
7 | Rx0+ | I | +LVDS Differential Data Input | |
8 | GND | P | Ground | |
9 | Rx0- | I | -LVDS Differential Data Input | |
10 | RxC+ | I | +LVDS Differential Clock Input | |
11 | GND | P | Ground | |
12 | RxC- | I | -LVDS Differential Clock Input | |
13-16 | NC | - | No connection | |
17 | GND | P | Ground | |
18 | 5V | P | Power Supply | |
19 | Detect | I/O | Hot plug detect |
I: input, O: output, P: Power
4. RTP USB PIN Definition (CON3)
Pin | Symbole | Fonction | Remark |
---|---|---|---|
1 | 5V | Power Supply (5V) | |
2 | D- | Data line - | |
3 | D+ | Data line + | |
4 | NC | No connection | |
5 | GND | Power Ground |