Home Produtos LCD TFT Display LCD IPS TFT WF24LTYAJDNN0

Model No. WF24LTYAJDNN0

►Tamanho: 2,4 polegadas
►Resolução: 240 x 320 pontos
►Direção de exibição: IPS
►Interface: MCU, SPI
►Controlador ILI9341V integrado
►Placa de controle: Não
►Brilho (cd/m²): 500
►Quadro com furo passante: Não
►Tela de Toque: Não

DRAWING

2.4" IPS Color TFT Module - WF24LTYAJDNN0 - Winstar Display

SPECIFICATIONS

Função do pino de interface

NO Símbolo Função I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(2.5 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire
9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to IOVCC or GND.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to IOVCC level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to IOVCC level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system.
Fix to GND level when not in use.
I/O
30 RESET (RESX)This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode

MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at IOVCC or GND.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB
interface mode
Fix to GND level when not in use.
I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDA SDA : Serial in/out signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at IOVCC or GND.
I/O
40 NC Not used, open this pin N

Especificações Gerais

Item Dimensão Unidade
Tamanho 2,4 polegadas
Matriz de pontos 240 × RGB × 320(TFT) pontos
Dimensão do módulo 42.72(W) × 60.26(H) × 2.8(D) mm
Área ativa 36.72 × 48.96 mm
Distância entre pontos 0.153 × 0.153 mm
Tipo LCD TFT, Preto, Transmissivo
Controller IC ILI9341V ou equivalente
Direção de exibição 80/80/80/80
Relação de aspecto Portrait
Tipo de luz de fundo LED, Branco
Painel de toque Sem painel de toque
Superfície Reflexo

Classificações Máximas Absolutas

Item Símbolo Valor Min Valor Típico Valor Máximo Unidade
Temperatura de operação TOP -20 +70
Temperatura de armazenamento TST -30 +80

Características Eletrônicas

Item Símbolo Valor Min Valor Típico Valor Máximo Unidade
Supply Voltage For Analog VCI 2.5 3.3 V
Supply Voltage For Logic IOVCC 2.5 3.3 V
Supply Current For LCM ICC IOVCC=VCI =VCC=3.0V 6 9 mA
go top
close