우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
WEP012832A 모델은 모듈에 용량성 터치 패널이 있는 확장 항목을 가지고 있습니다. 대각선 크기는 2.23인치이며, 128x32 도트 매트릭스로 구성되어 있습니다. 이 OLED 모듈은 SSD1305 IC가 내장되어 있으며, 6800/8080 8비트 병렬, I2C 및 4-Wire SPI 인터페이스를 지원합니다. 논리 전압 공급은 3.3V이며, 50% 체크 보드 전류로 표시될 때 85mA @3.3VDD (일반값)이고, 드라이빙 듀티는 1/32이며, 논리 전압 공급은 3.0V~5.0V(VDD)입니다. 이 모델은 모듈에 용량성 터치 패널이 있으며, I2C 인터페이스를 지원하는 FT6336U IC가 내장되어 있으며, 1개의 손가락에 대한 감지점이 있으며, 보통의 빛깔 표면 유리로 되어 있습니다.
WEP012832A-CTP 모델은 PCB가 장착된 COG OLED 디스플레이입니다. 모듈을 고객의 응용 프로그램에 고정하는 데 사용할 수 있는 두 가지 방법이 있습니다. 하나는 모듈을 고정하는 마운팅 홀을 사용하는 것이고, 다른 하나는 PCB 보드에 금속 핀을 사용하는 것입니다. 또한 고객이 선택할 수 있는 연결 인터페이스 옵션 세 가지를 제공합니다. 핫바 인화, 금속 핀 또는 커넥터가 있는 FPC입니다. 또한 미니 진동 모터와 버저를 선택적으로 제공합니다.
이 OLED 모듈은 스마트 홈 응용 프로그램, 의료 기기, 스마트 제어 등에 적합합니다. WEP012832A-CTP 모듈은 -20℃에서 +70℃까지의 온도에서 작동할 수 있으며, 저장 온도 범위는 -40℃에서 +85℃입니다.
항목 | 치수 | 단위 |
---|---|---|
도트 매트릭스 | 128 x 32 | Dots |
모듈 치수 | 66.5 x 35.0 x 10.55(Max) | mm |
활성 영역 | 55.018 x 13.098 | mm |
도트 크기 | 0.408 x 0.388 | mm |
도트 피치 | 0.43 x 0.41 | mm |
디스플레이 모드 | 패시브 매트릭스 | |
디스플레이 색상 | Monochrome | |
Drive Duty | 1/32 Duty | |
IC | SSD1305 | |
OLED 인터페이스 | 6800, 8080, 4-Wire SPI, I2C | |
크기 | 2.23 인치 |
CTP IC | FT6336U |
터치포인트 | 1 |
CTP 인터페이스 | I2C |
표면 | 눈부심 |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4.0 | V |
Supply Voltage for Display | V0 | 0 | 16.0 | V |
작동 온도 | TOP | -20 | +70 | °C |
보관 온도 | TSTG | -40 | +85 | °C |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Power Supply Voltage | VDD | -0.3 | 3.6 | V |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 3.2 | 3.3 | 3.5 | V |
Supply Voltage for Display | V0 | - | 12.0 | 12.5 | 13.0 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | IOUT = 100uA, 3.3MHz | 0.9×VDD | - | VDD | V |
Output Low Volt. | VOL | IOUT = 100uA, 3.3MHz | 0 | - | 0.1×VDD | V |
Operating Current for VDD 50% Check Board | IDD | V0 =12.5V | - | 85 | 128 | mA |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage | VDD | - | 2.8 | 3.0 | 3.3 | V |
Input High Volt. | VIH | - | 0.7xVDD | - | VDD | V |
Input Low Volt. | VIL | - | -0.3 | - | 0.3xVDD | V |
Output High Volt. | VOH | IOH = -0.1mA | 0.7xVDD | - | - | V |
Output Low Volt. | VOL | IOH = 0.1mA | - | - | 0.3xVDD | V |
No. | 기호 | 기능 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground. | |||||||||||||||
2 | VDD | Power supply pin for core logic operation. | |||||||||||||||
3 | V0 | Keep float (i.e. disable). Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
4 | D/C# | This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
5 | R/W# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
6 | E/RD# | When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO) and the chip is selected. When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
7~14 | DB0~DB7 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
15 | CS# | This pin is the chip select input. (active LOW) | |||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDDIO) during normal operation. |
|||||||||||||||
17,18 | BS1, BS2 | Communicating Protocol Select. These pins are MCU interface selection input. See the following table:
|
|||||||||||||||
19 | N.C. | No connection. | |||||||||||||||
20 | FG(GND) | Ground. | |||||||||||||||
21 | TP_SCK | I2C Clock | |||||||||||||||
22 | TP_SDA | I2C Data | |||||||||||||||
23 | TP_INT | Interrupt Output This pin is used as the dedicated interrupt output signal. |
|||||||||||||||
24 | TP_RST | Hardware Reset This pin is to reset hardware for this chip. |
|||||||||||||||
25 | TP_VDD | Power supply pin for only touch panel (3.3V). | |||||||||||||||
26 | VSS | Ground. | |||||||||||||||
27 | N.C. | No connection. | |||||||||||||||
28 | N.C. | No connection. |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책