COG 액정 디스플레이 128x64

모델 번호 WO12864D3

►128*64 COG 디스플레이
►그래픽 LCD
►IC: ST7565P
►3.3V 전원 공급 장치
►1/64 듀티 사이클
►인터페이스 : 6800/8080/SPI

PDF 다운로드

데모 코드 조회에 추가

이전 목록으로 돌아가기 다음

도면

Winstar WO12864D3 - 128x64 COG Displays (Chip on Glass Display)

Data source ref:WO12864D3-TFH#

사양

인터페이스 핀 기능

Pin No.

기호

Level

설명

/CS1

The chip select signal

/RES

When RES is set to “L”, the setting are initialized.

This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.

/WR(R/W)

• When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.

/RD(E)

• When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
• When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.

6~13

D0~D7

I/O

Data bus line

VDD

Power
Supply

Power supply

VSS

Power
Supply

Ground

VOUT

DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD

CAP5+

DC/DC voltage converter

CAP3+

CAP1-

CAP1+

CAP2+

CAP2-

CAP4+

VRS

Power
Supply

This is the internal-output VREG power supply for the LCD power supply voltage
regulator.

Power
Supply

This is a multi-level power supply for the liquid crystal drive.

Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
IRS = “L” : the V0 voltage regulator internal resistors are not used.
IRS = “H” : the V0 voltage regulator internal resistors are used.

C86

This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface

P/S

This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:

P/S	Data/Command	Data	Read/Write	Serial Clock
"H"	A0	D0 to D7	/RD,/WR	X
"L"	A0	SI(D7)	Write only	SCL(D6)

When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM

/HPM

This is the power control terminal for the power supply circuit for liquid crystal drive.
/HPM = “H”: Normal mode
/HPM = “L”: High power mode

IRS

This terminal selects the resistors for the V0 voltage level adjustment.
IRS = “H”: Use the internal resistors
IRS = “L”: Do not use the internal resistors. The V0 voltage level is
regulated by an external resistive voltage divider attached to the VR terminal

기계적 데이터

항목	치수	단위
점의 수	128 x 64	－
모듈 치수	80.0 x 54.0 x 9.5	mm
보기 영역	70.7 x 38.8	mm
활성 영역	66.52 x 33.24	mm
도트 크기	0.48 x 0.48	mm
도트 피치	0.52 x 0.52	mm
듀티	1/64 , 1/9 Bias
역광 타입	LED
IC	ST7565P
인터페이스	6800/8080/4-Line SPI

절대 최대 정격값

항목	기호	최소값	대표값	최대값	단위
작동 온도	TOP	-20	－	+70	℃
보관 온도	TST	-30	－	+80	℃
Power Supply Voltage	VDD	-0.3	－	3.6	V
Power supply voltage (VDD standard)	V0,VOUT	-0.3	－	14.5	V
Power supply voltage (VDD standard)	V1,V2,V3,V4	-0.3	－	V0+0.3	V

전기적 특성

항목	기호	조건	최소값	대표값	최대값	단위
Supply Voltage For Logic	VDD-VSS	－	2.7	－	3.3	V
Supply Voltage For LCM	V0-VSS	Ta=-20℃ Ta=25℃ Ta=70℃	10.0 9.8 9.6	10.2 10.0 9.8	10.4 10.2 10.0	V V V
Input High Volt.	VIH	－	0.8 VDD	－	VDD	V
Input Low Volt.	VIL	－	VSS	－	0.2VDD	V
Output High Volt.	VOH	－	0.8VDD	－	VDD	V
Output Low Volt.	VOL	－	VSS	－	0.2VDD	V
Supply Current(No include LED Backlight)	IDD	－	－	0.6	1.0	mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd

COG 액정 디스플레이 128x64

도면

사양

인터페이스 핀 기능

기계적 데이터

절대 최대 정격값

전기적 특성

관련 제품

WO12864H