Moduli TFT IPS 2.4"
Modello numero WF24LTYAJDNN0
►Dimensione : 2.4 pollici
►Risoluzione : 240 x 320 punti
►Direzione di visione : IPS
►Interfaccia : MCU, SPI
►Driver IC:ILI9341V
►Scheda di controllo: No
►Luminosità (cd/m²): 500
►Cornice di fissaggio: No
►Touch Screen: senza pannello touch
Descrizione
WF24LTYAJDNN0 è un modulo di visualizzazione IPS TFT-LCD da 2,4 pollici con una risoluzione di 240 x 320 pixel. Il modulo WF24L è dotato del controller IC ILI9341V, che supporta sia le interfacce MCU8080 che SPI. Presenta un pannello IPS che offre vantaggi come un angolo di visione più ampio di Sinistra: 80 / Destra: 80 / Su: 80 / Giù: 80 gradi (tipico), un rapporto di contrasto di 800 (valore tipico) e una luminosità di 500 nits (valore tipico), con un pannello superficiale antiriflesso.
Questo display TFT-LCD da 2,4 pollici è in modalità ritratto e integra il controller IC ILI9341V sul modulo. La tensione di alimentazione per l'analogico (VCI) varia da 2,5V a 3,3V. Il modulo TFT può funzionare in un intervallo di temperature da -20°C a +70°C, con temperature di conservazione comprese tra -30°C e +80°C. Questo display versatile è adatto a varie applicazioni, tra cui test di qualità dell'aria, misurazione della glicemia, lettori MP3, elettrodomestici, nonché applicazioni specializzate come contachilometri, sistemi di monitoraggio della sicurezza, dispositivi portatili e telecamere da cruscotto in apparecchiature industriali compatte.
DISEGNO
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
NO | Simbolo | Funzione | I/O |
---|---|---|---|
1 | GND | Ground | P |
2-6 | NC | No connection | - |
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P |
8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P |
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O |
10 | CS | Chip select signal. | I |
11 | D/CX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I |
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I |
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I |
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O |
30 | RESET | (RESX)This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I |
31 | IM0 | Select the MCU interface mode MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I |
32 | IM1 | ||
33 | IM2 | ||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O |
35 | DB17 | ||
36 | LEDK | Cathode of LED backlight. | P |
37 | LEDK | Cathode of LED backlight. | P |
38 | LEDA | Anode of LED backlight. | P |
39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O |
40 | NC | Not used, open this pin | N |
Specifiche generali
Articolo | Dimensioni | Unità |
---|---|---|
Dimensione (Diagonale) | 2.4 | pollici |
A matrice di punti (Risoluzione) | 240 × RGB × 320(TFT) | punti |
Dimensione del modulo | 42.72(W) × 60.26(H) × 2.8(D) | mm |
Area attiva | 36.72 × 48.96 | mm |
Passo del Dot | 0.153 × 0.153 | mm |
Tipo LCD | TFT, Nero, Trasmissivo | |
Driver IC | ILI9341V o equivalente | |
Direzione di visione | 80/80/80/80 | |
Proporzioni dell’area visiva (ratio) | Portrait | |
Tipo di backlight | LED, Bianco | |
Touch Screen | senza touch screen | |
Superficie | Bagliore (Glare) |
Valori massimi assoluti
Articolo | Simbolo | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|
Temperatura di lavoro | TOP | -20 | - | +70 | ℃ |
Temperatura di stock | TST | -30 | - | +80 | ℃ |
Caratteristiche elettriche
Articolo | Simbolo | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|
Supply Voltage For Analog | VCI | 2.5 | — | 3.3 | V |
Supply Voltage For Logic | IOVCC | 2.5 | — | 3.3 | V |
Supply Current For LCM | ICC | IOVCC=VCI =VCC=3.0V | 6 | 9 | mA |