Interfaccia SPI / 6800 / 8080 Display COG 240x64
Modello numero WO24064D
►LCD COG
►LCD Grafico
►240 x 64 unti
►IC: ST7586S
►Alimentatore + 3.3V
►1/64 duty cycle
►Interfaccia : 6800/8080/SPI
Descrizione
WO24064D è un modulo LCD grafico COG monocromatico con formato a matrice di punti 240x64. Il display LCD grafico standard COG 240 x 64 di Winstar, modello WO24064D, è dotato di un circuito integrato ST7586S che supporta l'interfaccia SPI / 6800 / 8080 e un'interfaccia opzionale a 4 linee SPI o a 3 linee SPI. Il modulo ha dimensioni di 86,2 x 39,3 mm, con un'area attiva di 76,78 x 20,46 mm. Questo modulo LCD può funzionare a temperature comprese tra -20°C e +70°C. La tensione di alimentazione logica va da 3,0V a 3,4V, con un valore tipico di 3,3V e un duty cycle di guida di 1/64. Questo display LCD COG è particolarmente adatto per macchine mediche, strumenti di test, sistemi di sicurezza domestica, apparecchiature di controllo industriale, ecc.
DISEGNO
Data source ref:WO24064D-TFH#
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
Pin No. | Simbolo | Level | descrizione | ||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VG | P | VG is the power of SEG-drivers. | ||||||||||||||||||||
2 | XV0 | P | Negative operating voltage of COM-drivers. | ||||||||||||||||||||
3 | V0 | P | Positive operating voltage of COM-drivers. V0O is the output of the positive Vop generator. V0I is the positive Vop supply of LCD drivers. V0S is the sensor of the positive Vop generator. V0O, V0I & V0S should be separated on ITO and be connected together by FPC. |
||||||||||||||||||||
4 | VM | P | VM is the non-select voltage level of COM-drivers. | ||||||||||||||||||||
5 | VDDA | P | Analog power for internal booster. | ||||||||||||||||||||
6 | VSS | P | Ground | ||||||||||||||||||||
7 | VD1 | P | VD1I is the power source of digital circuits. | ||||||||||||||||||||
8 | VDDI | P | Power of interface I/O circuit. | ||||||||||||||||||||
9 | CSB | Input | Chip select input pin. CSB=“L”: This chip is selected and the MPU interface is active. CSB=“H”: This chip is not selected and the MPU interface is disabled (D[7:0] are high impedance). |
||||||||||||||||||||
10 | IF3 | Input | These pins select interface operation mode.
|
||||||||||||||||||||
11 | IF2 | ||||||||||||||||||||||
12 | IF1 | ||||||||||||||||||||||
13 | RSTB | Input | Reset input pin. When RSTB is “L”, internal initialization procedure is executed. | ||||||||||||||||||||
14 | /RD(E) | Input | Read / Write execution control pin. (This pin is only used in parallel interface) | ||||||||||||||||||||
15 | D7 | I/O | The bi-directional data bus of the MPU interface. When CSB is “H”, they are high impedance. If using serial interface: D0 is the SDA signal in 4-Line & 3-Line interface. D1 is the A0 signal in 4-Line interface |
||||||||||||||||||||
16 | D6 | ||||||||||||||||||||||
17 | D5 | ||||||||||||||||||||||
18 | D4 | ||||||||||||||||||||||
19 | D3 | ||||||||||||||||||||||
20 | D2 | ||||||||||||||||||||||
21 | D1 | ||||||||||||||||||||||
22 | D0 | ||||||||||||||||||||||
23 | NC | No connection | |||||||||||||||||||||
24 | /WR(R/W) | Input | Read / Write execution control pin. (This pin is only used in parallel interface) | ||||||||||||||||||||
25 | A0(SCL) | Input | The function of this pin is different in parallel and serial interface. In parallel interface: A0 is register selection input. A0 = "H": inputs on data bus are display data; A0 = "L": inputs on data bus are command. _ In serial interface: this pad will be used as SCL (serial-clock) input |
||||||||||||||||||||
26 | VSS | P | Ground |
Dati meccanici
Articolo | Dimensioni | Unità |
---|---|---|
Number of Dots | 240 x 64 | - |
Dimensione del modulo | 86.2 x 39.3 x 5.1 | mm |
Area di visualizzazione | 80.8 x 24.8 | mm |
Area attiva | 76.78 x 20.46 | mm |
Dimensioni del Dot | 0.30 x 0.30 | mm |
Passo del Dot | 0.32 x 0.32 | mm |
Duty | 1/64 | |
Tipo di backlight | LED | |
IC | ST7586S | |
Interfaccia | 6800/8080/3-Line/4-Line |
Valori massimi assoluti
Articolo | Simbolo | Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|
Temperatura di lavoro | TOP | -20 | - | +70 | ℃ |
Temperatura di stock | TST | -30 | - | +80 | ℃ |
Digital Power Supply Voltage | VDDI | -0.3 | - | 3.6 | V |
Analog Power supply voltage | VDDA | -0.3 | - | 3.6 | V |
LCD Power supply voltage | V0-XV0 | -0.3 | - | 19 | V |
LCD Power supply voltage | VG | -0.3 | - | 5.5 | V |
Caratteristiche elettriche
Articolo | Simbolo | Condition | Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|---|
Supply Voltage For Logic | VDD-VSS | - | 3.0 | 3.3 | 3.4 | V |
Supply Voltage For LCM | XV0-V0 | Ta=-20℃ Ta=25℃ Ta=70℃ |
- 9.8 - |
- 10.0 - |
- 10.2 - |
V V V |
Input High Volt. | VIH | - | 0.7 VDD | - | VDD | V |
Input Low Volt. | VIL | - | VSS | - | 0.3VDD | V |
Output High Volt. | VOH | - | 0.8VDD | - | VDD | V |
Output Low Volt. | VOL | - | VSS | - | 0.2VDD | V |
Supply Current(No include LED Backlight) | IDD | VDD=3.3V | - | 1.5 | - | mA |
Search Keyword: lcd 240x64, lcd 240 x 64, 240x64 lcd, 240 x 64 lcd