产品叙述
WF24MTLAJDNT0 为2.4寸直屏电阻式触控 SPI TFT 显示器模块,分辨率为240x320 像素。模块内建 ST7789V 驱动IC 支持4线SPI接口,模拟电源电压(Vcc) 2.4V~3.6V ;标准值为3.3V。此型号模块使用防眩光表面面板,视角为6点钟方向;灰阶反转为12点钟方向。此款WF24MTLAJDNT0直屏TFT LCD模块亮度为350 nits (典型值),对比度500:1。模块工作温度范围-20°C~+70°C;储存温度范围-30°C~+80°C。另外,我们还提供无触控面板型号 WF24MTLAJDNN0 供客户选择。
规格图
产品规格
Pin功能定义
LCM PIN定义
NO | 符号 | 功能说明 | ||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | ||||||||||||||||||
2 | VLED+ | Anode of LED backlight. | ||||||||||||||||||
3 | VLED- | Cathode of LED backlight. | ||||||||||||||||||
4 | GND | Ground | ||||||||||||||||||
5 | VCC | Power supply | ||||||||||||||||||
6 | RESET | System reset pin. (RESX) signal is active low |
||||||||||||||||||
7 | SDA | When IM3: Low, SPI interface input/output pin. When IM3: High, SPI interface input pin. The data is latched on the rising edge of the SCL signal. If not used, please fix this pin at VDDI or DGND level. |
||||||||||||||||||
8 | DCX(SCL) | This pin is used to be serial interface clock. DCX=’1’: display data or parameter. DCX=’0’: command data. If not used, please fix this pin at VDDI or DGND. |
||||||||||||||||||
9 | CSX | Chip selection pin Low enable. High disable. |
||||||||||||||||||
10 | WRX(D/CX) | Display data/command selection pin in 4-line serial interface. Second Data lane in 2 data lane serial interface. If not used, please fix this pin at VDDI or DGND. |
||||||||||||||||||
11 | GND | Ground | ||||||||||||||||||
12 | SDO(DOUT) | SPI interface output pin. The data is output on the falling edge of the SCL signal. If not used, let this pin open. |
||||||||||||||||||
13 | TE | Tearing effect signal is used to synchronize MCU to frame memory writing. If not used, please let this pin open |
||||||||||||||||||
14 | IM3 | The MCU interface mode select.
|
||||||||||||||||||
15 | GND | Ground | ||||||||||||||||||
16 | XR | Right electrode | ||||||||||||||||||
17 | YD | Bottom electrode | ||||||||||||||||||
18 | XL | Left electrode | ||||||||||||||||||
19 | YU | Top electrode | ||||||||||||||||||
20 | GND | Ground |
规格说明
项目 | 规格 | 单位 |
---|---|---|
显示尺寸(对角线) | 2.4 | 寸 |
点阵(分辨率) | 240 × RGB × 320(TFT) | dots |
模块尺寸 | 42.72(W) × 60.26(H) × 3.43(D) | mm |
有效区域 | 36.72 × 48.96 | mm |
点间距 | 0.153 × 0.153 | mm |
LCD 类型 | TFT, 正常白, 透射式 | |
接口 | SPI | |
TFT 驱动IC | ST7789V 或相容IC | |
视角 | 6点钟方向 | |
灰阶反转 | 12点钟方向 | |
长宽比 | 直屏 | |
背光类型 | LED, 正常白 | |
触控面板类型 | RTP 电阻式触控面板 | |
表面 | 防眩光 |
最大绝对额定值
项目 | 符号 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|
工作温度 | TOP | -20 | - | +70 | ℃ |
储存温度 | TST | -30 | - | +80 | ℃ |
电气特性
项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|---|
模拟电源电压 | Vcc | - | 2.4 | 3.3 | 3.6 | V |
LCM供电电流 | Icc | - | - | 6.4 | 9.6 | mA |