1.5 дюйма COG монохромный OLED дисплей 128x128
Артикул. WEO128128A
►Тип: Графический
►Тип монтажа контроллера: COG
►Диагональ: 1.5 дюйма
►Разрешение: 128 x 128 точек
►IC:SSD1327
►3V Power supply
►1/128 duty
►Интерфейс: 6800, 8080, SPI, I2C
►Цвет дисплея: Белый / Желтый
►Инверсия
►Other FPC options available in below table
Описание
Чертеж
Data source ref: WEO128128ALAP3N00000
Технические характеристики
Функции контроллера контактного интерфейса
No. | Символы | Описание | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||||
4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||||||
5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||||||
6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select. Bus Interface selection
|
||||||||||
7 | BS2 | |||||||||||
8 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
9 | IREF | This pin is the segment output current reference pin | ||||||||||
10 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||
11 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
12 | D/C | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
||||||||||
13 | W/R# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. |
||||||||||
14 | RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
15 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||
16 | D1 | |||||||||||
17 | D2 | |||||||||||
18 | D3 | |||||||||||
19 | D4 | |||||||||||
20 | D5 | |||||||||||
21 | D6 | |||||||||||
22 | D7 | |||||||||||
23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
24 | VSS | Ground pin. |
Механические характеристики
Наименование | Измерения | Единица |
---|---|---|
Разрешение | 128 x 128 Dots | - |
Габариты | 33.80 x 36.50 x 2.05 | mm |
Активная область | 26.86 x 26.86 | mm |
Размер пикселя | 0.185 x 0.185 | mm |
Шаг пикселя | 0.210 x 0.210 | mm |
Матрица | Пассивная | |
Цвет дисплея | монохромные | |
Рабочий цикл | 1/128Duty | |
IC | SSD1327 | |
Интерфейс | 6800,8080,SPI,I2C | |
Диагональ | 1.5 дюйма |
Абсолютные максимальные значения
Parameter | Символы | Минимальный | Максимальный | Единица |
---|---|---|---|---|
Supply Voltage for Operation | VCI | -0.3 | 4.0 | V |
Напряжение питания логических схем | VDD | -0.5 | 2.75 | V |
Напряжение питания дисплея | VCC | -0.5 | 19.0 | V |
Диапазон рабочих температур | TOP | -40 | +80 | °C |
Температура хранения | TSTG | -40 | +85 | °C |
Электронные характеристики
Наименование | Символы | Condition | Минимальный | Типичный | Максимальный | Единица |
---|---|---|---|---|---|---|
Low voltage power supply, power supply for I/O pins | VCI | 2.8 | 3 | 3.3 | V | |
Напряжение питания дисплея | VCC | - | 14 | 14.5 | 15 | V |
Напряжение питания логических схем | VDD | - | 2.4 | - | 2.6 | V |
Вход высокого уровня | VIH | - | 0.8×VCI | - | VCI | V |
Вход низкого уровня | VIL | - | 0 | - | 0.2×VCI | V |
Выход высокого уровня | VOH | - | 0.9×VCI | - | VCI | V |
Выход низкого уровня | VOL | - | 0 | - | 0.1×VCI | V |
50% Check Board operating Current | VCC =14.5V | - | 24 | 36 | mA |
FPC Options:
Drawing | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
---|---|---|---|---|---|---|---|
25.05 | 24 | 0.5 | ZIF | 6800,8080,SPI,I2C | FPC2050002411XXXXX03 | 20150901 | |
41 | 24 | 0.5 | ZIF | 6800,8080,4-Wire SPI,I2C | FPC2050002411XXXXX12 | 20200116 |
Search keyword: 128x128 oled, oled 128x128, 1.5 oled, 1.5" oled, 1.5 дюйма oled, oled 1.5 дюйма, oled 1.5"