2.7" 128x64 дюймовый COG OLED с емкостной сенсорной тач панелью
Numer modelu WEO012864Q-CTP
►Typ: graficzny (bez ramki)
►Struktura: COG
►Rozmiar: 2.7"
►128 x 64 matryca punktowa
►IC:SSD1309
►zasilanie 3V
►wypełnienie 1/64
►Interfejs: 6800, 8080, SPI, I2C
►Panel dotykowy: pojemnościowy panel dotykowy (CTP)
►Punkty dotyku : 1 Palec
►Kolor wyświetlacza: biały / żółto / jasnoniebieski / zielony
Opis
WEO012864Q-CTP to popularny moduł wyświetlacza OLED COG o przekątnej 2,7 cala z pojemnościowym panelem dotykowym w module; o rozdzielczości 128x64 punktów. Moduł ten jest wyposażony w układ SSD1309, obsługuje interfejs równoległy 6800/8080 8-bitowy, SPI 4-żyłowy i I2C, napięcie zasilania dla logiki wynosi od 2,8V do 3,3V, wartość typowa 3,0V, napięcie zasilania dla wyświetlacza 13V, obowiązek pracy 1/64. Model WEO012864Q-CTP został wyposażony w układ dotykowy GT911, obsługujący interfejs I2C, oraz wykrywający jeden punkt dla pojemnościowego ekranu dotykowego.
Ten model WEO012864Q o przekątnej 2,7 cala z CTP jest idealny do zastosowań w inteligentnych domach, inteligentnych urządzeniach technologicznych, systemach energetycznych, urządzeniach pomiarowych, systemach komunikacyjnych, przyrządach medycznych, itp. Moduł ten może działać w temperaturach od -20°C do +70°C; jego temperatura przechowywania mieści się w zakresie od -30°C do +80°C. Dzięki wysokiemu współczynnikowi kontrastu wynoszącemu 10 000:1 i rozszerzonemu kątowi widzenia do 160°, moduł OLED zapewnia wyraźniejsze obrazy.
Rysunek
Data source ref: WEO012864QWPP3D00F00
Specyfikacja
Funkcja pinów interfejsu
No. | Symbol | Funkcja | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | NC(GND) | No connection | |||||||||||||||
2 | VLSS | This is an analog ground pin | |||||||||||||||
3 | VSS | Ground. | |||||||||||||||
4 | NC | No connection | |||||||||||||||
5 | VDD | Power supply pin for core logic operation | |||||||||||||||
6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
7 | BS2 | ||||||||||||||||
8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
10 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
11 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
12 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
13-20 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
21 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
22 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
24 | NC(GND) | No connection |
CTP PIN Definition
No. | Symbol | Funkcja |
---|---|---|
1 | GND | Power ground |
2 | VDD | Power supply |
3 | INT | Interrupt signal, active low, asserted to request Host start a new transaction |
4 | SDA | I2C data signal |
5 | SCL | I2C clock signal |
6 | RST | External reset signal, active low |
7 | GND | Power ground |
8 | GND | Power ground |
9 | GND | Power ground |
10 | GND | Power ground |
Dane mechaniczne
Rzecz | Wymiar | Jednostka |
---|---|---|
Matryca punktowa | 128 × 64 | - |
Wymiary modułu | 74.8 × 44.16 × 3.66 | mm |
Obszar aktywny | 61.41 × 30.69 | mm |
Wielkość piksela | 0.45 × 0.45 | mm |
Raster pomiędzy pikselami | 0.48 × 0.48 | mm |
Tryb wyświetlania | matryca | |
Kolor wyświetlacza | Monochromatyczny | |
Drive Duty | 1/64 Duty | |
IC | SSD1309 | |
Interfejs | 6800,8080,4-Wire SPI,I2C | |
Rozmiar (Przekątna) | 2.7 cale | |
CTP IC | GT911 | |
Punkty dotyku | 1 | |
CTP Interfejs | I2C | |
Powierzchnia | Glare |
Bezwzględne oceny maksymalne
Bezwzględne oceny maksymalne
Parameter | Symbol | Minimalna wartość | Maksymalna wartość | Jednostka |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4 | V |
Supply Voltage for Display | VCC | 0 | 15 | V |
Temperatura pracy | TOP | -20 | +70 | °C |
Temperatura przechowywania | TSTG | -30 | +80 | °C |
Touch Panel Controller GT911
Parameter | Symbol | Minimalna wartość | Maksymalna wartość | Jednostka |
---|---|---|---|---|
Power Supply Voltage | VDD | 2.66 | 3.47 | V |
Parametry elektryczne
DC Parametry elektryczne
Rzecz | Symbol | Stan | Minimalna wartość | Typowa wartość | Maksymalna wartość | Jednostka |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 12.5 | 13 | 13.5 | V |
High Level Input | VIH | - | 0.8×VDD | - | - | V |
Low Level Input | VIL | - | - | - | 0.2×VDD | V |
High Level Output | VOH | - | 0.9×VDD | - | - | V |
Low Level Output | VOL | - | - | - | 0.1×VDD | V |
50% Check Board operating Current | VCC =13.0V | - | 30 | 50 | mA |
Touch Panel Controller GT911
Rzecz | Symbol | Minimalna wartość | Typowa wartość | Maksymalna wartość | Jednostka |
---|---|---|---|---|---|
Supply Voltage | VDD | 2.8 | 3.0 | 3.3 | V |
Input High Volt. | VIH | 0.75xVDD | VDD+0.3 | V | |
Input Low Volt. | VIL | -0.3 | - | 0.25xVDD | V |
Output High Volt. | VOH | 0.85xVDD | - | - | V |
Output Low Volt. | VOL | - | - | 0.15xVDD | V |
Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 inch oled, oled 2.7