首页 产品介绍 OLED显示屏 图形 OLED 显示屏 WEO009664B-ZIF

1.1寸OLED显示器 96x64 - ZIF

型号 WEO009664B-ZIF

►类型:图形OLED
►结构:COG+ ZIF FPC
►1.1寸OLED
►96 x 64点阵
►内置控制器SSD1327
►3V电源电压
►1/64 duty
►接口:6800,8080,SPI,I2C
►穿戴式电子产品适用

产品叙述

WEO009664B是一款1.1寸的PM OLED显示器模块,分辨率96x64 pixels, 帶ZIF FPC。此款模块内建SSD1327 IC,模块操作支持 6800/8080 8-bit 并行接口,I2C与4-线SPI接口,3V电压驱动,1/64 duty与支持16灰阶。此款1.1" COG结构 WEO009664B模块可视为2017年EOL的TAB结构 1.1" WEX009664A/B的替代方案选项,两者的AA区尺寸接近都是1.1寸薄型OLED模块。

1.1" 的WEO009664B是小尺寸COG结构的OLED,无需背光非常轻薄 ,非常适用于携带式装置、智能医疗产品、个人健康守护追踪装置、量测仪器,智能家电、穿戴式装置等产品。此模块的工作温度是-40℃至+80℃,储存温度-40℃至+85℃。

  • WEO009664BL : 黄色

 

规格图

Small OLED Screen, OLED Display Screen, 1.1 OLED Screen Module - WEO009664B

产品规格

Pin功能定义

No. 符号 说明
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.
Bus Interface selection
 
BS[2:1] Interface
0 4 line SPI
1 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel

Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 BS2
8 VSS Ground pin. It must be connected to external ground.
9 IREF This pin is the segment output current reference pin
10 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
11 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
12 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
13 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
14 E This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
24 VSS Ground pin.

规格说明

项目 尺寸 单位
分辨率 96 × 64 Dots
模块尺寸 29.00 × 22.50 × 1.65 mm
检视区域 22.53 × 15.01 mm
像素大小 0.205 × 0.205 mm
像素间距 0.235 × 0.235 mm
显示模式 被动矩阵
显示颜色 单色
驱动方式 1/64 Duty
IC SSD1327
界面 4-Wire SPI, I2C, 6800, 8080
尺寸 1.1寸

电气特性

项目 符号 条件 最小值 典型值 最大值 单位
逻辑电源电压 VCI 2.8 3.0 3.3 V
显示电源电压 VCC 8.0 8.5 9.0 V
输入高电压 VIH 0.8×VCI VCI V
输入低电压 VIL VSS 0.2×VCI V
输出高电压 VOH 0.9×VCI VCI V
输低高电压 VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=8.5V 13.0 26.0 mA

最大绝对额定值

参数 符号 最小值 最大值 单位
工作电源电压 VCI -0.3 4.0 V
逻辑电源电压 VDD -0.5 2.75 V
显示电源电压 VCC -0.5 19.0 V
工作温度 TOP -40 +80 °C
储存温度 TSTG -40 +85 °C

Search keyword: 96x64 oled, oled 96x64, 1.1 oled, 1.1" oled, 1.1寸 oled, oled 1.1, oled 1.1"
go top
close