Ana sayfa Ürünler TFT LCD Ekran Standart TFT LCD Modülü WF57BTIACDNGE

5.7 inç Kapasitif Dokunmatik Panel TFT LCD Ekran

Model No. WF57BTIACDNGE

►Boyut : 5.7 inç
►Çözünürlük : 320 x 240 dot
►Görünüm yönü : 12H
►Ara yüz : RGB
►IC Part No.: --
►Kontrol Kartı : Hayır
►Parlaklık (cd/m²) : 400
►Delikli Çerçeve : Yes
►Dokunmatik Ekran: Kapasitif dokunmatik panelle birlikte (PCAP)
►O-Film : Seçenek

ÇIZIM

5.7 inch PCAP TFT LCD Display Module - WF57BTIACDNGE

AYRINTILAR

Arayüz Pin Fonksiyonlari

LCM PIN Definition

Pin Sembol Fonksiyon
1 IF1 Input data format control
2 IF2 Input data format control
3 POL Polarity Signal connect to VCOM driving circuit.
4 RESET Hardware reset
5 SPENA Chip select
6 SPCL Serial Clock
7 SPDA Serial Data
8 B0 Blue Data bit
9 B1 Blue Data bit
10 B2 Blue Data bit
11 B3 Blue Data bit
12 B4 Blue Data bit
13 B5 Blue Data bit
14 B6 Blue Data bit
15 B7 Blue Data bit
16 G0 Green Data bit
17 G1 Green Data bit
18 G2 Green Data bit
19 G3 Green Data bit
20 G4 Green Data bit
21 G5 Green Data bit
22 G6 Green Data bit
23 G7 Green Data bit
24 R0 Red Data bit
25 R1 Red Data bit
26 R2 Red Data bit
27 R3 Red Data bit
28 R4 Red Data bit
29 R5 Red Data bit
30 R6 Red Data bit
31 R7 Red Data bit
32 Hsync Horizontal synchronous signal
33 Vsync Vertical synchronous signal
34 Data CLK Dot data clock
35 AVDD(analog) Analog power: 4.5V~5.5V
36 AVDD(analog) Analog power: 4.5V~5.5V
37 VCC(Digital) Digital power: 3V~3.6V
38 VCC(Digital) Digital power: 3V~3.6V
39 NPC NTSC/PAL mode Auto detection result H:NTSC/L:PAL
40 VGL Gate off power
41 VGL Gate off power
42 UD Up/down selection
43 VGH Gate on power
44 LRC Shift direction of device internal shift register control.
45 GND System ground pin of the IC.
Connect to system ground.
46 VCOM VCOM driving input
47 VCOM VCOM driving input
48 ENB Signal to settle the horizontal display position
49 GND System ground pin of the IC.
Connect to system ground.
50 GND System ground pin of the IC.
Connect to system ground.

PCAP PIN Definition

Pin Sembol Fonksiyon
1 VSS System ground pin of the IC. Connect to system ground.
2 VDDT Power Supply : +3.0V
3 SCL I2C clock input
4 NC No connect
5 SDA I2C data input and output
6 NC No connect
7 /RST External Reset, Low is active
8 NC No connect
9 /INT External interrupt to the host
10 VSS System ground pin of the IC. Connect to system ground.

Genel Özellikler

Kalem Ölçü Birim
Boyut (Köşegen) 5.7 inç
Nokta Matrisi (Çözünürlük) 320 × RGB × 240 (TFT) dots
Modül ölçüleri 160(W) × 109(H) × 9.985 (D) mm
Aktif alan 115.2 × 86.40 mm
Nokta sıklığı 0.12 × 0.36 mm
LCD Tipi TFT, Beyaz, İletici
Görünüm yönü 12 o'clock
Gray Skala Enverziyonu Yönü 6 o'clock
TFT Arayüz 24-bit RGB
Görünüm Oranı 4:3
Backlight Tipi LED, Beyaz
PCAP IC FT5426 veya eşdeğer
PCAP Arayüz I2C
PCAP FW Versiyonu 0x03
Dokunmatik Ekran Kapasitif Dokunmatik Panel (PCAP)
Yüzey Parlama

Maksimum Değerler

Kalem Sembol Minumum Deger Tipik Deger Maksimum Deger Birim
Çalışma Sıcaklığı TOP -20 +70
Saklama Sıcaklığı TST -30 +80

Elektronik Özellikleri

Kalem Sembol Durum Minumum Deger Tipik Deger Maksimum Deger Birim
Supply Voltage For LCM VCC 3.0 3.3 3.6 V
Supply Voltage For Touch VDDT 2.8 3.3 V
Supply Current For LCM ICC 17 25 mA
Input High Volt. VIH 0.7 VCC VCC V
Input Low Volt. VIL 0 0.3 VCC V
LCD Driving
Supply Voltage
VGH 15 V
VGL -10 V
VCOMH 2.5 5.5 V
VCOML -2.0 0 V
AVDD 4.5 5.0 5.5 V
go top
close