หน้าแรก ผลิตภัณฑ์ TFT LCD Standart Renkli TFT LCD WF28KTLAJDNT0

หมายเลขรุ่น WF28KTLAJDNT0

►ขนาด : 2.8 นิ้ว
►ความละเอียด : 240×320 จุด
►ทิศทางการมอง : 6H
►อินเตอร์เฟซ : SPI
►IC ไดรเวอร์:ST7789V
►แผงควบคุม : No
►ความสว่าง (cd/m²) : 350
►เฟรมแบบ รูทะลุ : No
►หน้าจอสัมผัส : พร้อมแผงระบบสัมผัส (หน้าจอ) แบบ Resistive

การร่าง

2.8 TFT SPI 240x320, 2.8 inch SPI Interface TFT Color Display - WF28KTLAJDNT0

ข้อมูลจำเพาะ

คุณสมบัติการปักไว้ที่อินเตอร์เฟส

LCM PIN Definition

NO สัญลักษณ์ คุณสมบัติการทำงาน
1 GND Ground
2 VLED+ Anode of LED backlight.
3 VLED- Cathode of LED backlight.
4 GND Ground
5 VCC Power supply
6 RESET System reset pin. (RESX)
signal is active low
7 SDA When IM3: Low, SPI interface input/output pin.
When IM3: High, SPI interface input pin.
The data is latched on the rising edge of the SCL signal.
If not used, please fix this pin at VDDI or DGND level.
8 DCX(SCL) This pin is used to be serial interface clock.
DCX=’1’: display data or parameter.
DCX=’0’: command data.
If not used, please fix this pin at VDDI or DGND.
9 CSX Chip selection pin
Low enable.
High disable.
10 WRX(D/CX) Display data/command selection pin in 4-line serial interface.
Second Data lane in 2 data lane serial interface.
If not used, please fix this pin at VDDI or DGND.
11 GND Ground
12 SDO(DOUT) SPI interface output pin.
The data is output on the falling edge of the SCL signal.
If not used, let this pin open.
13 TE Tearing effect signal is used to synchronize MCU to frame memory
writing.
If not used, please let this pin open
14 IM3 The MCU interface mode select.
IM3 IM2 IM1 IM0 MPU Interface Mode Data pin
0 1 1 0 4-line 8bit serial I/F SDA: in/out
1 1 1 0 4-line 8bit serial I/F II SDA: in/SDO: out
15 GND Ground
16 XR Right electrode
17 YD Bottom electrode
18 XL Left electrode
19 YU Top electrode
20 GND Ground

ข้อกำหนดทั่วไป

รายการ ขนาด หน่วย
ขนาด 2.8 นิ้ว
ความละเอียด 240 x RGB x 320(TFT) dots
ขนาดโมดูล 50.0(W) x 69.2(H) x 3.48(D) mm
พื้นที่ที่ใช้งานอยู่ 43.2 x 57.6 mm
ระดับจุด 0.18 x 0.18 mm
ประเภท LCD TFT, ขาว, ทรานสมิสซีฟ
อินเตอร์เฟซ SPI
TFT IC ไดรเวอร์ ST7789V หรือเทียบเท่า
ทิศทางการมอง 6 o'clock
ทิศทางการผกผันระดับสีเทา 12 o'clock
อัตราส่วนภาพ Portrait
ประเภทแสงไฟพื้นหลัง LED, ขาว
หน้าจอสัมผัส พร้อมแผงระบบสัมผัส (หน้าจอ) แบบ Resistive
พื้นผิว แสงจ้า

คะแนนสูงสุด

รายการ สัญลักษณ์ ค่าต่ำสุด ค่าปกติ ค่าสูงสุด หน่วย
อุณหภูมิในการทำงาน TOP -20 +70
อุณหภูมิในการจัดเก็บ TST -30 +80

ลักษณะทางอิเล็กทรอนิก

รายการ สัญลักษณ์ ค่าต่ำสุด ค่าปกติ ค่าสูงสุด หน่วย
Supply Voltage For Analog Vcc 2.4 3.3 3.6 V
Supply Current For LCM Icc 6.7 10.0 mA
go top
close