หน้าแรก ผลิตภัณฑ์ โมดูล OLED โมดูล OLED + Touch Screen WEO012832M-CTP

หมายเลขรุ่น WEO012832M-CTP

►ประเภท: กราฟฟิก
►โครงสร้าง: COG
►ขนาด: 0.91 นิ้ว
►128 x 32 Dot Matrix
►IC:SSD7317
►แหล่งจ่ายไฟ 3V
►1/32 duty
►อินเตอร์เฟซ: SPI/I2C
►In-Cell Touch Panel
►สีการแสดงผล: ขาว / สีเหลือง

รายละเอียด

 

การร่าง

0.91 inch 128x32 In-Cell Touch Panel OLED Display, In-Cell Display - WEO012832M-CTP

 

Data source ref: WEO012832MWAP3J00000

ข้อมูลจำเพาะ

คุณสมบัติการปักไว้ที่อินเตอร์เฟส

No. สัญลักษณ์ คุณสมบัติการทำงาน
1 VCI Power supply pin for touch analog driving. VCI must be greater than or equal to VDD.
2 VSS Ground pin.
3 VCC Power Supply for Display. Most positive voltage. Connect to external source.
4 VSL This is segment voltage (output low level) reference pin.
When external VSL is not used, connect externally to VSS. When external VSL is used, connect with resistor and diode to ground
5 DCDCEN0 Enable output pin for external DCDC circuit. NC if not used
6 DCDCEN1 Enable input pin for external DCDC circuit. Tie low if not used.
7 VDD Power supply pin for core logic operation.
8 FR This pin outputs RAM write synchronization signal.
It should be kept NC if it is not used.
9 DCS This pin is the chip select input connecting to the MCU for display interface.
10 TCS This pin is the chip select input connecting to the MCU for touch.
11 RES# This pin is the reset signal input for display interface.
12 TRES This pin is the reset signal input for touch.
13 DC This pin is Data/Command control pin for display interface.
In I2C mode, this pin acts as SA0 for slave address selection.
14 E/RD# In I2C mode, this pin acts as SA1 for slave address selection.
15 IRQ Interrupt signal for touch reporting.
16 TD0 Serial Data Input/Output and clock for Touch
In SPI mode TD2 serves as SDOUT, TD1 serves as SDIN, and TD0 serves as the serial clock SCLK.
In I2C mode TD2 and TD1 should be tied together and serve as SDA and TD0 is the serial clock SCL. External pull up resistors.
17 TD1
18 TD2
19 VSS Ground pin.
20 D0 The serial clock input for display interface.
21 D1 The serial data input for display interface.
22 BS1
BS1 BS3 Display Interface Touch Interface
0 0 4 -SPI SPI
0 1 4-SPI I2C
1 0 I2C SPI
1 1 I2C I2C
23 BS3
24 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

ข้อมูลเชิงกล

รายการ ขนาด หน่วย
ความละเอียด 128 × 32 Dots
ขนาดโมดูล 30.0 × 11.5 × 1.41 mm
พื้นที่ที่ใช้งานอยู่ 22.38 × 5.58 mm
ขนาดจุด 0.155 × 0.155 mm
ระดับจุด 0.175 × 0.175 mm
โหมดการแสดงผล พาสซีฟเมทริกซ์
สีการแสดงผล ขาวดำ
Drive Duty 1/32 Duty
IC SSD7317
OLED อินเตอร์เฟซ 4-wire SPI,I2C
CTP อินเตอร์เฟซ SPI,I2C
Gesture 4-key and 1-D slide
ขนาด (เส้นทแยงมุม) 0.91 นิ้ว

คะแนนสูงสุด

Parameter สัญลักษณ ค่าต่ำสุด ค่าสูงสุด หน่วย
Supply Voltage for Logic VDD 0 4.0 V
Supply Voltage for Logic VCI 0 4.0 V
Supply Voltage for Display VCC 0 19 V
อุณหภูมิในการทำงาน TOP -40 +80 °C
อุณหภูมิในการจัดเก็บ TSTG -40 +85 °C

ลักษณะทางอิเล็กทรอนิก

DC ลักษณะทางอิเล็กทรอนิก

รายการ สัญลักษณ์ เงื่อนไข ค่าต่ำสุด ค่าปกติ ค่าสูงสุด หน่วย
Supply Voltage for Logic VDD 1.65 3.3 3.5 V
Touch controller Supply Voltage VCI 3.0 3.5 V
Supply Voltage for Display VCC 8.0 8.5 9.0 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current ICC VCC =8.5V 4 8 mA
 

Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 นิ้ว oled, oled 0.91 นิ้ว

go top
close