На главную страницу Продукция OLED Дисплей Графический OLED дисплей WEP012832A

128x32 Органические светодиоды 2.23"

Артикул. WEP012832A

►Тип: Графический
►Тип монтажа контроллера: COG + Frame + PCB
►Диагональ: 2.23 дюйма
►Разрешение: 128 x 32 точек
►IC:SSD1305
►3V Power supply
►1/32 duty
►Интерфейс: 6800, 8080, SPI, I2C
►Цвет дисплея: Белый / Желтый / Синего

Описание

Winstar выпустила новый OLED модуль COG + PCB модель WEP012832A; диагональ модуля 2.23” с разрешением 128x32 точек. WEP012832A сделан на базе контроллера IC SSD1305, поддержка интерфейсов: параллельного 6800/8080 8-Бит, I2C и четырехжильного SPI интерфейса. Напряжение питания 3 ~ 5V.

Модель WEP012832A имеет 20 пин металлический штырьевой контакт и крепежные отверстия на плате. Мы предоставляем мини вибромотор и зуммер (на выбор) для индикатора, так же можно выбрать вариант для пайки или же версию с пин выводами + FPC шлейф (артикулы различаются).

Этот 2.23” дюймовый OLED модуль прекрасно подойдет для таких применений как: настенные измерительные приборы, POS системы, Облачные loT устройства, устройства интеллектуальных технологий, энергосистемы, автомобильной индустрии, средств связи, медицинских инструментов и т.д. Модуль WEP012832A может работать при температурах от -40 ° С до + 80 ℃; а температура хранения - от -40 ℃ до + 85 ℃.

 

Чертеж

WEP012832A

Data source ref: WEP012832AWPP3N00000

Технические характеристики

Функции контроллера контактного интерфейса

No. Символы Описание
1 VSS Ground.
2 VDD Power supply pin for core logic operation.
3 V0 Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
4 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
6 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO) and the chip is selected.
When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
7~14 DB0~DB7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 CS# This pin is the chip select input. (active LOW)
16 RES# This pin is reset signal input. When the pin is LOW, initialization of the chip is executed.
Keep this pin HIGH (i.e. connect to VDDIO) during normal operation.
17,18 BS2,BS1 Communicating Protocol Select.
These pins are MCU interface selection input. See the following table:
  68XX-parallel 80XX-parallel Serial I2C
BS1 0 1 0 1
BS2 1 1 0 0
19 N.C. No connection.
20 FG(GND) Ground.
21~25 N.C. No connection.
26 VSS Ground.
27 BSW Control the Piezoelectric Buzzer.
28 MSW Control the BLDC Vibration Motor.

Механические характеристики

Наименование Измерения Единица
Разрешение 128 × 32 Dots
Габариты 66.5 × 35.0 × 9.0(Max) mm
Активная область 55.018 × 13.098 mm
Размер пикселя 0.408 × 0.388 mm
Шаг пикселя 0.43 × 0.41 mm
Матрица Пассивная
Цвет дисплея монохромные
Рабочий цикл 1/32 Duty
IC SSD1305
Buzzer OBO-11241SB
Vibration Motor W0625AB001F
Интерфейс 6800, 8080, SPI, I2C
Диагональ 2.23 дюйма

전기적 특성

Наименование Символы Кондиция Минимальный Типичный Максимальный Единица
Напряжение питания логических схем VDD 3.0 3.3 3.5 V
Высокое входное напряжение VIH 0.8×VDD VDD V
Низкое входное напряжение VIL 0 0.2×VDD V
Выход высокого уровня VOH IOUT = 100uA, 3.3MHz 0.9×VDD VDD V
Вход высокого уровня VOL IOUT = 100uA, 3.3MHz 0 0.1×VDD V
Supply Voltage for Buzzer BSW 50% square 0.8×VDD VDD V
Supply Voltage for Vibration Motor MSW 2.7 3.3 V
Operating Current at Display with 50% Check Board IDD VDD=3.3V 90 120 mA

Электронные характеристики

Параметр Символы Минимальный Максимальный Единица
Напряжение питания логических схем VDD -0.3 4.0 V
Диапазон рабочих температур TOP -40 +80 °C
Температура хранения TSTG -40 +85 °C

Search keyword: 128x32 oled, oled 128x32, 2.23 oled, 2.23" oled, 2.23 дюйма oled, oled 2.23, oled 2.23"
go top
close