Display OLED 128x32 de 2,23 polegadas com Painel Tátil Capacitivo
Model No. WEP012832A-CTP
►Tipo: Gráfico
►Estrutura: COG + Frame + PCB
►Tamanho: 2,23 polegadas
►Matriz de pontos 128×32
►IC:SSD1305
►Alimentação +3V
►1/32 duty cycle
►Interface: 6800, 8080, SPI, I2C
►Tela de Toque: Com painel de toque capacitivo (CTP)
►Detect Point : 1 Finger
►Display Color: Branco / Amarelo / Azul
Descrição
O modelo WEP012832A possui um item de extensão com Painel Tátil Capacitivo no módulo; tem tamanho diagonal de 2,23 polegadas, composto por uma matriz de pontos 128x32. Este módulo OLED é integrado com o IC SSD1305; ele suporta a interface paralela 6800/8080 de 8 bits, I2C e 4 fios SPI, a tensão de alimentação para a lógica é de 3,3V, a corrente da placa de 50% é de 85mA @3,3VDD (valor típico), o dever de condução é de 1/32, a tensão de alimentação para a lógica é de 3,0V a 5,0V (VDD). Este modelo possui um Painel Tátil Capacitivo no módulo; ele é integrado com o IC FT6336U que suporta interface I2C, um ponto de detecção para tela de toque capacitiva.
O modelo WEP012832A-CTP é uma tela OLED COG com um PCB no módulo. Existem duas opções de métodos para fixar os módulos nas aplicações dos clientes; uma é usar furos de montagem para fixar os módulos, a outra é usar pinos metálicos na placa de circuito. Além disso, fornecemos três opções de conexão de interface para os clientes escolherem, soldagem de barra quente, pinos metálicos ou FPC com conector. Também fornecemos um motor de vibração miniatura e um buzzer opcional.
Este módulo OLED é adequado para aplicativos de casa inteligente, dispositivos médicos, sistemas de controle inteligente, etc. O módulo WEP012832A-CTP pode operar em temperaturas de -20℃ a +70℃; sua faixa de temperaturas de armazenamento varia de -40℃ a +85℃.
DRAWING
Data source ref: WEP012832AWPP3D00001
SPECIFICATIONS
Função do pino de interface
No. | Símbolo | Função | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground. | |||||||||||||||
2 | VDD | Power supply pin for core logic operation. | |||||||||||||||
3 | V0 | Keep float (i.e. disable). Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
4 | D/C# | This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
5 | R/W# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
6 | E/RD# | When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO) and the chip is selected. When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
7~14 | DB0~DB7 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
15 | CS# | This pin is the chip select input. (active LOW) | |||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDDIO) during normal operation. |
|||||||||||||||
17,18 | BS1, BS2 | Communicating Protocol Select. These pins are MCU interface selection input. See the following table:
|
|||||||||||||||
19 | N.C. | No connection. | |||||||||||||||
20 | FG(GND) | Ground. | |||||||||||||||
21 | TP_SCK | I2C Clock | |||||||||||||||
22 | TP_SDA | I2C Data | |||||||||||||||
23 | TP_INT | Interrupt Output This pin is used as the dedicated interrupt output signal. |
|||||||||||||||
24 | TP_RST | Hardware Reset This pin is to reset hardware for this chip. |
|||||||||||||||
25 | TP_VDD | Power supply pin for only touch panel (3.3V). | |||||||||||||||
26 | VSS | Ground. | |||||||||||||||
27 | N.C. | No connection. | |||||||||||||||
28 | N.C. | No connection. |
Dados Mecânicos
Item | Dimensão | Unidade |
---|---|---|
Matriz de pontos | 128 x 32 Pontos | - |
Dimensão do módulo | 66.5 x 35.0 x 10.55(Max) | mm |
Área ativa | 55.018 x 13.098 | mm |
Tamanho do ponto | 0.408 x 0.388 | mm |
Distância entre pontos | 0.43 x 0.41 | mm |
Modo de exibição | Passive Matrix | |
Cor de exibição | Monochrome | |
Drive Duty | 1/32 Duty | |
IC | SSD1305 | |
OLED Interface | 6800, 8080, 4-Wire SPI, I2C | |
Tamanho | 2,23 polegadas |
CTP IC | FT6336U |
Detect Point | 1 |
CTP Interface | I2C |
Superfície | Reflexo |
Classificações Máximas Absolutas
Parameter | Símbolo | Valor Min | Valor Máximo | Unidade |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4.0 | V |
Supply Voltage for Display | V0 | 0 | 16.0 | V |
Temperatura de operação | TOP | -20 | +70 | °C |
Temperatura de armazenamento | TSTG | -40 | +85 | °C |
Touch Panel Controller FT6336U
Parameter | Símbolo | Valor Min | Valor Máximo | Unidade |
---|---|---|---|---|
Power Supply Voltage | VDD | -0.3 | 3.6 | V |
Características Eletrônicas
DC Características Eletrônicas
Item | Símbolo | Condição | Valor Min | Valor Típico | Valor Máximo | Unidade |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 3.2 | 3.3 | 3.5 | V |
Supply Voltage for Display | V0 | - | 12.0 | 12.5 | 13.0 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | IOUT = 100uA, 3.3MHz | 0.9×VDD | - | VDD | V |
Output Low Volt. | VOL | IOUT = 100uA, 3.3MHz | 0 | - | 0.1×VDD | V |
Operating Current for VDD 50% Check Board | IDD | V0 =12.5V | - | 85 | 128 | mA |
Touch Panel Controller FT6336U
Item | Símbolo | Condição | Valor Min | Valor Típico | Valor Máximo | Unidade |
---|---|---|---|---|---|---|
Supply Voltage | VDD | - | 2.8 | 3.0 | 3.3 | V |
Input High Volt. | VIH | - | 0.7xVDD | - | VDD | V |
Input Low Volt. | VIL | - | -0.3 | - | 0.3xVDD | V |
Output High Volt. | VOH | IOH = -0.1mA | 0.7xVDD | - | - | V |
Output Low Volt. | VOL | IOH = 0.1mA | - | - | 0.3xVDD | V |