Home Produtos LCD COG WO12864U

Display LCD COG Gráfico de 128x64 ST7565P

Model No. WO12864U

►LCD COG 128x64
►LCD Gráfico
►IC: ST7565P
►Alimentação 3,3V
►1/64 duty cycle, 1/9 bias
►Interface : 6800/8080/SPI

Descrição

DRAWING

128x64 COG LCD Display Module (ST7565P) - WO12864U

SPECIFICATIONS

Função do pino de interface

Pin No. Símbolo I/O Descrição
1 VDD ­_ Power supply pin for logic.
2 VSS _ Ground pin, connected to 0V
3 /CS1 I Chip select input pin. Interface access is enabled when CS1B is "L" and CB2 is "H" . When chip is on-active (CS1B="H" or CS2="L"), D[7:0] pins are high impedance.
4 CS2
5 /RES I Hardware reset input pin. When RSTB is "L", internal initialization is executed and the internal registers will be initialized.
6 A0 I It determines whether the access is related to data or command.
A0=“H”: Indicates that signals on D[7:0] are display data.
A0=“L”: Indicates that signals on D[7:0] are command.
7 R/W I Read/Write execution control pin. When PSB is "H",
C86 MPU Type RWR Descrição
H 6800 series R/W Read/Write control input pin.
R/W="H": read
R/W="L": write
L 8080 series /WR Write enable input pin.
Signals on D[7:0] will be latched at the rising edge of /WR signal.

RWR is not used in serial interface and should fix to "H" by VDD.
8 E I Read/Write execution control pin. When PSB is "H",
C86 MPU Type ERD Descrição
H 6800 series E Read/Write control input pin.
R/W="H": When E is "H", D[7:0] are in output mode.
R/W="L": Signals on D[7:0] are latched at the falling edge of E signal
L 8080 series /RD Read enable input pin.
When /RD is "L", D[7:0] are in output mode.

ERD is not used in serial interface and should fix to "H" by VDD.
9-16 D0-D7 I/O Data bus line
17 C86 I C86 selects the microprocessor type in parallel interface mode.
PSB C86 Selected Interface
"H" "H" Parallel 6800 Series MPU Interface
"H" "L" Parallel 8080 Series MPU Interface
"L" "X" Serial 4-Line SPI Interface

Please refer to “APPLICATION NOTES” and “Microprocessor Interface” (Section 6) for detailed connection of the selected interface.
18 P/S I PSB selects the interface type: Serial or Parallel.

Especificações Gerais

Item Dimensão Unidade
Number of Characters 128 × 64
Dimensão do módulo 58.2 × 44.7 × 3.9(MAX) mm
Área de visualização 52.0 × 33.5 mm
Área ativa 47.76 × 30.29 mm
Tamanho do ponto 0.40 × 0.35 mm
Distância entre pontos 0.42 × 0.37 mm
Duty 1/64
Tipo de luz de fundo LED
IC ST7565P

Classificações Máximas Absolutas

Item Símbolo Valor Min Valor Típico Valor Máximo Unidade
Temperatura de operação TOP -20 +70
Temperatura de armazenamento TST -30 +80
Power Supply Voltage VDD -0.3 3.6 V
Power supply voltage (VDD standard) V0, VOUT -0.3 14.5 V
Power supply voltage (VDD standard) V1, V2, V3, V4 -0.3 V0+0.3 V

Características Eletrônicas

Item Símbolo Condição Valor Min Valor Típico Valor Máximo Unidade
Supply Voltage For Logic VDD-VSS 3.0 3.3 V
Supply Voltage For LCD VOP Ta=-20℃
Ta=25℃
Ta=70℃

8.3

8.5

8.7
V
V
V
Input High Volt. VIH 0.8VDD VDD V
Input Low Volt. VIL VSS 0.2VDD V
Output High Volt. VOH 0.8VDD VDD V
Output Low Volt. VOL VDD 0.2VDD V
Supply Current IDD VDD=3.3V 1 2 mA
go top
close