Model No. WO12864K
►LCD COG 128x64
►Controlador ST7565V integrado
►1/65 duty cycle, 1/9 bias
►Interface : 6800/8080/SPI
Data source ref: WO12864K-TMI#
Interface Pin Function
|1||/CS1||This is the chip select signal. When /CS1 = “L”, then the
chip select becomes active, and data/command I/O is enabled.
|2||/RES||I When /RES is set to “L,” the settings are initialized.
The reset operation is performed by the /RES signal level.
|3||A0||This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or a command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data
|4||/WR||• When connected to an 8080 MPU, this is active LOW.
(R/W) This terminal connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal.
• When connected to a 6800 Series MPU:
This is the read/write control signal input terminal. When R/W = “H”: Read.
When R/W = “L”: Write.
|5||/RD||• When connected to an 8080 MPU, this is active LOW.
(E) This pin is connected to the /RD signal of the 8080 MPU, and the
ST7565V series data bus is in an output status when this signal is “L”.
• When connected to a 6800 Series MPU, this is active HIGH. This is the 6800 Series MPU enable clock input terminal.
|6||D0||This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected (P/S = “L”) :
D7 : serial data input (SI) ; D6 : the serial clock input (SCL).
D0 to D5 are set to high impedance.
When the chip select is not active, D0 to D7 are set to high impedance.
|14||VDD||Shared with the MPU power supply terminal Vcc.|
|15||GND||This is a 0V terminal connected to the system GND.|
|16||VOUT||DC/DC voltage converter. Connect a capacitor between this terminal and
|17||CAP3-||DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1+ terminal.|
|18||CAP1+||DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.|
|19||CAP1-||DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1+ terminal.|
|20||CAP2-||DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2- terminal.|
|21||CAP2+||DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2+ terminal.|
|22||V1||This is a multi-level power supply for the liquid crystal drive. The voltage
Supply applied is determined by the liquid crystal cell, and is changed through the use of are sistive voltage divided or through changing the impedance using an op. amp. Voltage levels are determined based on VDD,
|27||VR||Output voltage regulator terminal. Provides the voltage between VDD and
V5 through a resistive voltage divider.
IRS = “L” : the V5 voltage regulator internal resistors are not used . IRS = “H” : the V5 voltage regulator internal resistors are used .
|28||C86||This is the MPU interface switch terminal.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 MPU interface.
|29||P/S||This is the parallel data input/serial data input switch terminal. P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
When P/S = “L”, D0 to D5 fixed “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM .
|30||IRS||This terminal selects the resistors for the V5 voltage level adjustment.
IRS = “H”: Use the internal resistors
IRS = “L”: Do not use the internal resistors. The V5 voltage level is
regulated by an external resistive voltage divider attached to the VR terminal
|Number of dots||128 x 64||－|
|Module dimension||89.7 x 49.8 x 6.0||mm|
|View area||66.8 x 35.5||mm|
|Active area||63.98 x 31.98||mm|
|Dot size||0.48 x 0.48||mm|
|Dot pitch||0.50x 0.50||mm|
|Duty||1/65 duty , 1/9 Bias|
Absolute Maximum Ratings
|Power Supply Voltage||VSS||-3.6||－||+0.3||V|
|Power Supply Voltage (VDD standard)||V5, VOUT||-13.5||－||+0.3||V|
|Power Supply Voltage (VDD standard)||V1, V2, V3, V4||V5||－||+0.3||V|
|Supply Voltage For Logic||VDD-VSS||－||2.8||3.0||3.2||V|
|Supply Voltage For LCD||VOP||Ta=-20℃
|Input High Volt.||VIH||－||0.8 VDD||－||VDD||V|
|Input Low Volt.||VIL||－||Vss||－||0.2 VDD||V|
|Output High Volt.||VOH||－||0.8 VDD||－||VDD||V|
|Output Low Volt.||VOL||－||Vss||－||0.2 VDD||V|
Search Keyword: lcd 128x64, lcd display 128x64, 128x64 lcd display