Strona główna Produkty Wyświetlacz OLED Graficzne Wyświetlacz OLED WEP012832A-CTP

2.23" 128x32 pojemnościowy panel dotykowy Wyświetlaczy OLED

Numer modelu WEP012832A-CTP

►Typ: graficzny
►Struktura: COG+FR+PCB
►Rozmiar: 2.23"
►128×32 matryca punktowa
►wbudowany kontroler SSD1305Z
►zasilanie 3V
►cykl wypełnienia 1/32
►interfejs: 6800, 8080, SPI, I2C
►Panel dotykowy : pojemnościowy panel dotykowy

Opis

  • WEP012832AWPP3D00000 : biały

Rysunek

2.23 128x32 Capacitive Touch OLED Display - WEP012832A-CTP - Winstar Display

Specyfikacja

Funkcja pinów interfejsu

No. Symbol Funkcja
1 VSS Ground.
2 VDD Power supply pin for core logic operation.
3 V0 Keep float (i.e. disable). Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
4 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
6 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO)
and the chip is selected.
When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
7~14 DB0~DB7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 CS# This pin is the chip select input. (active LOW)
16 RES# This pin is reset signal input. When the pin is LOW, initialization of the chip is executed.
Keep this pin HIGH (i.e. connect to VDDIO) during normal operation.
17,18 BS2,BS1 Communicating Protocol Select.
These pins are MCU interface selection input. See the following table:
  68XX-parallel 80XX-parallel Serial I2C
BS1 0 1 0 1
BS2 1 1 0 0
19 N.C. No connection.
20 FG(GND) Ground.
21 TP_SCK I2C Clock
22 TP_SDA I2C Data
23 TP_INT Interrupt Output
This pin is used as the dedicated interrupt output signal.
24 TP_RST Hardware Reset
This pin is to reset hardware for this chip.
25 TP_VDD Power supply pin for only touch panel (3.3V).
26 VSS Ground.
27 BSW Control the Piezoelectric Buzzer.
28 MSW Control the BLDC Vibration Motor.

Dane mechaniczne

Rzecz Wymiar Jednostka
Matryca punktowa 128 × 32 punktów
Wymiary modułu 66.5 × 35.0 × 10.55(Max) mm
Obszar aktywny 55.018 × 13.098 mm
Wielkość piksela 0.408 × 0.388 mm
Raster pomiędzy pikselami 0.43 × 0.41 mm
Tryb wyświetlania matryca
Kolor wyświetlacza Monochromatyczny
Drive Duty 1/32 Duty
IC SSD1305Z
OLED Interfejs 6800, 8080, SPI, I2C
CTP Interfejs I2C
Rozmiar 2.23 cale

Parametry elektryczne

DC Electrical Characteristics

Rzecz Symbol Stan Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD 3.2 3.3 3.5 V
Supply Voltage for Display V0 12.0 12.5 13.0 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH IOUT = 100uA, 3.3MHz 0.9×VDD VDD V
Output Low Volt. VOL IOUT = 100uA, 3.3MHz 0 0.1×VDD V
Operating Current for VDD IDD V0 =12.5V - 90 120 mA
Supply Voltage for Buzzer BSW VDD=5.0V
1/2 square
0.8×VDD VDD V
Supply Voltage
for Vibration Motor
MSW 2.7 3.3 V

Bezwzględne oceny maksymalne

Parameter Symbol Minimalna wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD -0.3 4.0 V
Supply Voltage for Display V0 0 16.0 V
Temperatura pracy TOP -40 +80 °C
Temperatura przechowywania TSTG -40 +85 °C

Search keyword: 128x32 oled, oled 128x32, 2.23 oled, 2.23" oled, 2.23 inch oled, oled 2.23, oled 2.23"
go top
close