May.2016-English         Issue No.90 www.winstar.com.tw
 
Issue No. 90

Welcome to read Winstar Newsletter issue no.90. In this issue, we will introduce Winstar new products; they are including TFT 3.5 inch WF35R, OLED 0.96 inch WEO012864C and STN Graphic WO256128A.

 
Contents
1. Product Introduction - 3.5 inch TFT WF35R
2. Product Introduction - 0.96” OLED WEO012864C
3. Product Introduction - Graphic COG LCD WO256128A

 

 

Product Introduction - 3.5 inch TFT WF35R

Winstar WF35R is a 3.5 inch diagonal full color QVGA 320x240 TFT LCD module. This module is built in with SSD2119 IC; it includes the controller and driver IC functions and supports lots of different interfaces: 8/ 9/ 16/ 18-bit 6800-series and 8080-series parallel interface, 3-wire or 4-wire SPI, 18-bit/6-bit RGB interface. Since the WF35R doesn’t require control-board to drive MCU parallel and SPI interface, the advantage of WF35R is having competitive price than other TFT models which are require control-board on module. Below is the basic spec information for WF35R, please contact with us if you need further detailed information.

Item-WF35R Dimension Unit
Size 3.5 inch
Dot Matrix 320 x RGBx240(TFT) dots
Module dimension 76.84(W) x 63.84(H) x 3.27(D) mm
Active area 70.08 x 52.56 mm
Dot pitch 0.073 x 0.219 mm
LCD type TFT, Normally White, Transmissive
View Direction 12 o'clock 
Gray Scale Inversion Direction 6 o'clock 
Backlight Type LED, Normally White
IC SSD2119
Interface RGB/MCU/SPI
Touch Panel CTP and RTP option
Surface Anti-Glare

Drawing and pin define for WF35R

Drawing and pin define for WF35R

 

No. Symbol Description No. Symbol Description
1~2 VCI Booster input voltage pin 15~32 D17~D0 Data bus
3 VSS Ground 33 VSS Ground
4 VDDIO Voltage input pin for logic 34 DOTCLK Dot-clock signal and oscillator source
5 VSS Ground 35 HSYNC Line Synchronous Signal
6 RESET Reset Signal pin (“Low” is enable) 36 VSYNC Frame Synchronous Signal
7 DC/SDC Data or Command select PIN. 37 DE Display enable pin for controller
8 E/RD 6800 system: E(enable signal) 38 VSS Ground
8080 system : RD(read strobe signal)
Serial mode: Not use and should be connected to VDDIO or VSS
9 WR 6800 system : RW (indicates read cycle when high ,write cycle when low) 39~42 PS0~PS3 Interface select PIN
8080 system : WR (write strobe signal)
10 CS Chip select 43 VSS Ground
11 SCL Serial Clock. 44~47 NC NC
12 SD0 Serial Data output 48 VSS Ground
13 SDI Serial Data Input 49 LEDK Backlight LED Cathode
14 WSYNC Ram write synchronization output. Leave it OPEN when not used. 50 LEDA Backlight LED Anode.
► Link to Winstar WF35R web page

 

TOP

 

 

Product Introduction - 0.96” OLED WEO012864C

Winstar WEO012864C is a small OLED display which is made of 128x64 pixels, diagonal size only 0.96 inch. The WEO012864C has the outline dimension of 26.70 x19.26 mm and AA size 21.74 x10.86 mm; it is built in with SH1106G controller IC and it communicates via 6800/8080 8-bit parallel, I2C and 4-wire serial interface. The WEO012864C is a small COG OLED display which is ultra thin (only 1.65mm); lightweight and low power consumption. It is suitable for handheld instruments, meters, mp3, wearable device, IoT, etc. The standard emitting color for this item is yellow, but options are available in white and sky blue.

WEO012864C module can be operating at temperatures from –40℃ to +80℃; its storage temperatures range from -40℃ to +80℃. Below is the basic specification of WEO012864C as reference. For any further information such as samples or quotation, please contact with our sales rep.

 

Item-WEO012864C Dimension
Dot Matrix 128 x 64
Module dimension 26.70 × 19.26 × 1.65 mm
Active Area 21.74 × 10.86 mm
Pixel Size 0.148 × 0.148 mm
Pixel Pitch 0.170 × 0.170 mm
Display Mode Passive Matrix
Display Color Yellow/Sky Blue/White
Drive Duty 1/64 Duty
Controller IC SH1106G
Interface 6800/8080/4-wire SPI/I2C
0.96” OLED WEO012864C
0.96” OLED WEO012864C
 

► Link to Winstar WEO012864C web page

 

 

TOP

 

 

Product Introduction - Graphic COG LCD WO256128A

WO256128A is a monochrome graphic LCD module made of 256x128 pixels, diagonal size 2.9 inch. This LCD Module WO256128A is built in with ST75256 controller IC, it supports 6800 8-bit, 8080 8-bit parallel and 4-wire serial SPI and I2C interface. The WO256128A is having the same outline dimension, and VA size and same power supply 3.3V as WO12864D3, but is having a much higher resolution and performance. The WO125128A is an upgrade version of WO12864D3 to meet with the customers’ requirement on higher resolution and the best thing is that the customers don’t have to change the mechanical design for their applications.

This module can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃. The WO256128A is available for different LCD mode options, STN Negative, FSTN Negative (Double film) and FSTN positive and with LED backlight options, like white LED. Please contact with us if you need different LCD type and LED combination.

Item-WO256128A Dimension
Number of dots 256 x 128
Module dimension 80.0 x 54.0 mm
View area 70.7 x 38.8 mm
Active area 66.54 x 33.26 mm
Dot size 0.24 x0.24 mm
Dot pitch 0.26 x 0.26 mm
LCD type (available) STN Negative, Blue Transmissive
FSTN Negative (Double film) Transmissive
FSTN Positive Transflective
Drive Method 1/128 DUTY, 1/12 BIAS
View direction 6 o’clock
Backlight Type LED, White
IC ST75256
Interface 6800/8080/SPI/I2C
Graphic COG LCD WO256128A

► Link to Winstar WO256128A web page

 

 

TOP

Friendly Printing