도면

사양
인터페이스 핀 기능
NO | 기호 | 기능 | I/O |
---|---|---|---|
1 | GND | Ground | P |
2-6 | NC | No connection | - |
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P |
8 | IOVCC | Low voltage power supply for interface logic circuits (1.65 ~ 3.3 V) |
P |
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O |
10 | CS | Chip select signal. | I |
11 | D/CX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to VDDI or VSS. |
I |
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to VDDI level when not in use. |
I |
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to VDDI level when not in use. |
I |
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. | I/O |
30 | RESET | This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I |
31 | IM0 | Select the MCU interface mode![]() MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. * : Fix this pin at VDDI or VSS. |
I |
32 | IM1 | ||
33 | IM2 | ||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. | I/O |
35 | DB17 | ||
36 | LEDK | Cathode of LED backlight. | P |
37 | LEDK | Cathode of LED backlight. | P |
38 | LEDA | Anode of LED backlight. | P |
39 | SDI(SDA) | When IM[3] : Low, Serial in/out signal. When IM[3] : High, Serial input signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at VDDI or VSS. |
I/O |
40 | SDO | Serial output signal. The data is outputted on the falling edge of the SCL signal. If not used, open this pin |
O |
일반 사양
항목 | 치수 | 단위 |
---|---|---|
크기 (대각선) | 2.4 | 인치 |
도트 매트릭스 (해상도) | 240 × RGB × 320(TFT) | dots |
모듈 치수 | 42.72(W) × 60.26(H) × 2.8(D) | mm |
활성 영역 | 36.72 × 48.96 | mm |
도트 피치 | 0.153 × 0.153 | mm |
LCD 유형 | TFT, 검은색, 투과성 | |
제어 IC | ILI9341V 또는 이와 동등한 | |
시야각 | 80/80/80/80 | |
종횡비 | Portrait | |
역광 타입 | LED,백색 | |
터치 패널 | 터치패널(스크린)이 없는 | |
표면 | 눈부심 |
절대 최대 정격값
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
작동 온도 | TOP | -20 | - | +70 | ℃ |
보관 온도 | TST | -30 | - | +80 | ℃ |
전기적 특성
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
Supply Voltage For Analog | VCI | 2.5 | — | 3.3 | V |
Supply Voltage For Logic | IOVCC | 2.5 | — | 3.3 | V |
Supply Current For LCM | ICI | — | 6 | 9 | mA |