도면
사양
인터페이스 핀 기능
Pin No. | 기호 | 기능 |
---|---|---|
1 | VCOM | Common voltage |
2 | VDD | Digital power |
3 | VDD | Digital power |
4 | NC | Not connect |
5 | Reset | Global reset pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability. Normally pull high. (R=10KΩ,C=1μF) |
6 | STBYB | Standby mode, normally pull high STBYB=”1”, normal operation STBYB=”0”,timing control, source driver will turn off, all output are high-Z |
7 | GND | Digital ground |
8 | RXIN0- | Negative LVDS differential data inputs |
9 | RXIN0+ | Positive LVDS differential data inputs |
10 | GND | Digital ground |
11 | RXIN1- | Negative LVDS differential data inputs |
12 | RXIN1+ | Positive LVDS differential data inputs |
13 | GND | Digital ground |
14 | RXIN2- | Negative LVDS differential data inputs |
15 | RXIN2+ | Positive LVDS differential data inputs |
16 | GND | Digital ground |
17 | RXCLKN- | Negative LVDS differential clock inputs |
18 | RXCLKN+ | Positive LVDS differential clock inputs |
19 | GND | Digital ground |
20 | RXIN3- | Negative LVDS differential data inputs |
21 | RXIN3+ | Positive LVDS differential data inputs |
22 | GND | Digital ground |
23 | NC | Not connect |
24 | NC | Not connect |
25 | GND | Digital ground |
26 | NC | Not connect |
27 | NC | Not connect |
28 | SELB | 6-bit/8-bit input select SELB = L , 8-bit ; SELB = H , 6-bit |
29 | AVDD | Analog power |
30 | GND | Digital ground |
31 | LED- | LED Cathode |
32 | LED- | LED Cathode |
33 | L/R | Left or right display control |
34 | U/D | Up / down display control |
35 | VGL | Negative power for TFT |
36 | NC | Not connect |
37 | NC | Not connect |
38 | VGH | Positive power for TFT |
39 | LED+ | LED Anode |
40 | LED+ | LED Anode |
When L/R=”1”,set left to right scan direction.
When U/D=”0”,set top to bottom scan direction.
When U/D=”1”,set bottom to top scan direction.
PCAP PIN Definition
Pin | 기호 | 기능 |
---|---|---|
1 | USB_VSS | System ground |
2 | USB_VDD 5V | Power supply |
3 | USB_D+ | Data + |
4 | USB_D- | Data - |
5 | VSS | System ground |
6 | SDA | I2C data input and output |
7 | SCL | I2C clock input |
8 | RST | External Reset, Low is active |
9 | INT | External interrupt to the host |
10 | VDDT 3.3 | Power supply |
일반 사양
항목 | 치수 | 단위 |
---|---|---|
크기 | 10.1 | 인치 |
도트 매트릭스 | 1024 RGB x 600 | dots |
모듈 치수 | 235(W) x 143(H) x 8.78(D) | mm |
활성 영역 | 222.72 (H) x 125.28(V) | mm |
도트 피치 | 0.2175(W) x 0.2088(H) | mm |
LCD 유형 | TFT, 검은색, 투과성 | |
인터페이스 | LVDS | |
드라이버 IC | EK79001HN + EK73215BCGA 또는 이와 동등한 | |
시야각 | 85/85/85/85 | |
종횡비 | 16:9 | |
백라이트 유형 | LED, 백색 | |
PCAP IC | ILI2511 또는 이와 동등한 | |
PCAP 인터페이스 | USB (I2C available) | |
PCAP FW 버전 | V6.0.0.0.62.90.1.2 | |
터치 패널 포함/제외 | PCAP | |
표면 | 눈부심 |
절대 최대 정격값
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
작동 온도 | TOP | -20 | - | +70 | ℃ |
보관 온도 | TST | -30 | - | +80 | ℃ |
전기적 특성
Typical Operation Conditions (At Ta = 25 °C,)
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
Digital Power Supply Voltage For LCD | VDD | 3 | 3.3 | 3.6 | V |
Analog Power Supply Voltage | AVDD | 9.89 | 10.2 | 10.5 | V |
Gate On Power Supply Voltage | VGH | 19.4 | 20.0 | 20.6 | V |
Gate Off Power Supply Voltage | VGL | -10.3 | -10.0 | -9.7 | V |
Common Power Supply Voltage | VCOM | 4.0 | 4.3 | 4.6 | V |
Input logic high voltage | VIH | 0.7 VDD | - | VDD | V |
Input logic low voltage | VIL | 0 | - | 0.3 VDD | V |
Supply PCAP | USB_VDD 5V | 4.4 | 5.0 | 5.5 | V |
I VDD 5V | — | 97.8 | 120 | mA |