제품 OLED 디스플레이 그래픽 OLED 디스플레이 WEO012864L-ZIF

1.28" 그래픽 OLED 디스플레이 (ZIF FPC)

모델 번호 WEO012864L-ZIF

►유형 : 그래픽(프레임 없이)
►구조 : COG + ZIF FPC
►크기 : 1.28 인치
►128x64 점 행렬
►3V 전원 공급 장치
►1/64 duty cycle
►인터페이스 : 6800 / 8080 / 3-SPI /4-SPI / I2C
►내장형 컨트롤러: SH1106G
►디스플레이 색상: 백색 / 노란색 / 하늘색

설명

도면

WEO012864L-ZIF - Winstar Display

사양

인터페이스 핀 기능

No. 기호 기능
1 NC(GND) No connection
2 C1N Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
3 C1P
4 C2P Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
5 C2N
6 VDD2 3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
This pin should be disconnected when VPP is supplied externally
7 NC No connection
8 VSS Ground.
9 VDD1 Power supply input: 1.65 - 3.5V
10 IM0 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI 3-wire SPI
IM0 0 0 0 0 1
IM1 1 1 0 0 0
IM2 1 0 1 0 0
11 IM1
12 IM2
13 CSB This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
14 RESB This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
15 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
16 WRB This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
17 RDB This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
18 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
27 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
28 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
29 VSL This is a segment voltage reference pad.
This pad should be connected to VSS externally.
30 NC(GND) No connection

기계적 데이터

항목 치수 단위
도트 매트릭스 128 x 64
모듈 치수 34.50 × 23.00 × 1.65 mm
활성 영역 29.42 × 14.20 mm
도트 크기 0.205 × 0.197 mm
도트 피치 0.230 × 0.222 mm
디스플레이 모드 패시브 매트릭스
디스플레이 색상 백색 / 노란색
Drive Duty 1/64 Duty
제어 IC SH1106G
인터페이스 6800/8080/3-SPI /4-SPI / I2C
크기 1.28 인치

절대 최대 정격값

Parameter 기호 최소값 최대값 단위
Supply Voltage for Logic VDD1 -0.3 3.6 V
Power supply for charge pump circuit VDD2 -0.3 4.8 V
Supply Voltage for Display VPP -0.3 14.5 V
작동 온도 TOP -40 +80 °C
보관 온도 TSTG -40 +85 °C

전기적 특성

DC 전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for Logic VDD1 2.8 3.0 3.3 V
Supply Voltage for Display VPP 6.75 7.25 7.75 V
High Level Input VIH 0.8xVDD1 VDD1 V
Low Level Input VIL VSS 0.2xVDD1 V
High Level Output VOH 0.8xVDD1 VDD1 V
Low Level Output VOL VSS 0.2xVDD1 V
50% Check Board operating Current VPP =7.25V 5.0 6.0 7.0 mA
 

Search keyword: 128x64 oled, oled 128x64, 1.28 oled, 1.28" oled, 1.28 인치 oled, oled 1.28, oled 1.28"

go top
close